Jump to content
SAU Community

Recommended Posts

18000 is cheap for a 300kw gtr I will also consider swaps.


So here it is,
It's an R32 GTR, I am the first Aussie owner as I imported it myself.

Mods:
GT35r twin bb turbo bought new from horsepowerinabox.com ( with turbo bag)
Stainless exhaust manifold
HKS 50mm external wastegate (screamer to atmosphere) Exhaust is now legal plumbed in with high flow stainless cat.
Apexi power fc de-jetro (map sensor not afm) with hand controller
4 inch inlet pipe to a 9 by 4 inch air filter fitted behind front bar vents (not in engine bay)
Adjustable HKS cam gears with new blue timing belt, gears have not been adjusted.
650cc injectors
Ceramic coated inlet manifold
4 inch cooler (not installed)
Front mounted ARC oil cooler ( fits where grill goes)
Fully adjustable pillow top ball joint suspension
Adjustable upper rear camber arms
Stainless Exhaust cat back
18 inch 5 spoke white Enkei rims, Excellent front rubber, rear not so good.
HKS evc3 boost controller,
800hp single plate clutch.
340kph dash
Rear hicas has been removed with a lock bar in place.
Sony cd player with AUX front plug for ipod with remote.

The car has 12 months rego on it, the clutch is only 5000kms old as is the gearbox ( gearbox with no reverse included if need be).
I have owned the car for about 3 years now and barely find time to drive it.
The car has been dynoed on a basic tune to 301.7 rwkws on 16psi, it has not been run at any higher boost levels. It is currently running on 10psi.

The condition of the car is quite good considering its age, there are a couple of scratch marks on the car id say from car parks, front passenger side on the bar and rear guard. The paint on the bonnet seems to have to no clear left on it, which is how it arrived from Japan.
When I purchased the car from Japan I was told the engine had been built with forged pistons and had some head work, but as I have not opened the motor I dont know for sure.

I am open to offers as I realise there is no chance of getting the money I have spent on it back.

rego: ATN48W
[removed]

post-21954-1183266092_thumb.jpg

post-21954-1183266298_thumb.jpg

post-21954-1183266223_thumb.jpg

post-21954-1183266357_thumb.jpg


Or swap

Link to comment
https://www.sau.com.au/forums/topic/174877-r32-gtr-single-turbo/
Share on other sites

  • Replies 76
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

nice car mate, i have seen this car cruising my area on numerous occasions. sounds tough as and looks the goods when cruising, best of luck selling it mate! cheers Garth

nice car mate, i have seen this car cruising my area on numerous occasions. sounds tough as and looks the goods when cruising, best of luck selling it mate! cheers Garth

Thanks champ, yeah I havnt seen your ride for a while now.

yeah my gtr is in the build, spoke to the machine shop today, my head is done... shall be on the road soon. hopefully u still have yours, we will have to cruise it up together! best of luck with your sale, nicest 32 ive seen ni awhile and tough street look...

Best of luck with it mate! you should have no worries selling it!

Garth

For sure Garth im in, if it doesnt sell. You could always buy it and have 2??? eh eh eh...nudge nudge.

Thanks Chris, I dont really want to sell it but its got to go.

Love this car, im just a bit short, might be in the market at the end of the year. Hopefully a car setup like this will be ready to take its place in my garage then GOODLUCK!

Not interested in a drift style setup S2 r33 gtst at all? thought id ask anyway..

  • 3 weeks later...
  • 2 weeks later...

hey thanks Andrew, looks like I wont be selling it. no one wants it, its in car point for 20 now...easy way to blow 40gs eh

Dude give me a call we gotta drink cans.....

Turbo conversion done by adriano sau member, all tunning done by DAT Dumah Auto Technics (02 43898111)

Cant remember suspension brand its pillow top ball joints though.

Hey mate very nice ride indeed.. ive got a gtst which im tryin to sell at the moment and then as soon as thats gone i will be gettin a bank loan for the extra cash.. if this is still for sale when ive sold mine and got the loan then i may be very interested.. how much lag does it have with the single or just at what rpm does it hit full boost?

Hey mate very nice ride indeed.. ive got a gtst which im tryin to sell at the moment and then as soon as thats gone i will be gettin a bank loan for the extra cash.. if this is still for sale when ive sold mine and got the loan then i may be very interested.. how much lag does it have with the single or just at what rpm does it hit full boost?

It comes on full boost around 4.

how does this 4 grand boost compare to stock??? how much laggier???

Im pretty sure full boost on a stocker should come on around 3250-3500 so doesnt seem too much laggier

Im pretty sure full boost on a stocker should come on around 3250-3500 so doesnt seem too much laggier

Its around the same as when it had the twins.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...