Jump to content
SAU Community

A31 From The Philippines

CEF

By CEF,
in Four door and wagon builds

 Share

Recommended Posts

CEF Contributor

CEF

Posted
Posted (edited)

103-0365_IMG.jpg

103-0364_IMG.jpg

103-0362_IMG.jpg

103-0349_IMG.jpg

Hello guys. I'm pretty new in posting here but I have been a constant browser of this forum. Here are some pics of my car. The engine is pretty much stock, RB24s and I will be swapping it out with the engine I got awhile back. I will post more pics of it as I do my car. Thank you.

Edited by CEF
Link to comment
https://www.sau.com.au/forums/topic/175140-a31-from-the-philippines/
Share on other sites
CEF Contributor

CEF

Posted
  • Author
Posted

Thank you so much for your comment. :thumbsup:

The wheels are 17" Work Rezax, 8" for the front and 9" for the back. Offset is +35 front and +47 rear. The offset is pretty good and the wheels are almost sticking out of the fenders. The car just needs to be lowered a little so as to lessen the gap between the fenders and tires but that will be done after I get all the parts from an r32 I ordered in Japan. It comes with all the goodies that I can put on the car. I'll take pics of the parts as they arrive with me.

  • 2 months later...
funkymonkey Grand Master

funkymonkey

Posted
Posted
NOTE THE PASSENGER SIDE AIR VENT !!!!!!!!!!!!!!!!!!!!!!
what about it? looks normal to me?

nice clean car... did they come out with those headlights and taillights in phillipines?

And you HAVE to put up pics of the legendard RB24S "carby RB" engine.

Also could you do me a huge favour and check on your headlight if it has the word "DOT" on it? AFAIK almost all cars sold in the phillipines were done to US standards, so that means that the LHD ceffies should have DOT approved headlights and tail lights.

  • 1 month later...
CEF Contributor

CEF

Posted
  • Author
Posted

Funkymoney,

Hi.

The headlights were released like that over here though I just installed some foglights in it as I don't like using the projector headlight models. The tailights Ihave on right now is from Japan. The a31's we have here have those horizontal lines across.

Yes, if you want some RB24 engine pics, I'll surely take some before I take them out in the coming weeks.

Headlights...no DOT markings on it. The tailights, I have to check again.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      R34 GT-T cycling ABS pump

      By Kinkstaah · Posted

      Lets say I wanted to buy this, specifically for this purpose. How do I actually perform the function. Can I still buy a Consult-1? Am I about to be burned by the fact my car is a 2000 model Series 2 R34 and thus will be some stupid other system? Do I just need this -> https://obd2australia.com.au/product/nissan-consult-14-pin-to-usb-ddl-diagnostic-interface-with-ftdi-ft232r-chip/ And with what software?
    • GTSBoy
      33 GTR Broken front wheel knuckle

      By GTSBoy · Posted

      That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • R32 TT
      33 GTR Broken front wheel knuckle

      By R32 TT · Posted

      Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • MBS206
      33 GTR Broken front wheel knuckle

      By MBS206 · Posted

      Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • GTSBoy
      R34 auto to manual conversion help

      By GTSBoy · Posted

      The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
×
×
  • Create New...