Jump to content
SAU Community

Recommended Posts

  • Replies 273
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

For shire ppl/st george ppl..

Slim is gonna msg me the time he leaves KK

I reckon there wil be some delays..

So maybe have some lunch at mccas, then come meet up at caltex at heatcote??

So slim- you reckon you will leave KK by 12pm?

get to caltex at heatcote around 12.30-12.40pm

^ this is some indication of the time to be at heatcote for those meeting us there.. cheers

For shire ppl/st george ppl..

Slim is gonna msg me the time he leaves KK

I reckon there wil be some delays..

So maybe have some lunch at mccas, then come meet up at caltex at heatcote??

So slim- you reckon you will leave KK by 12pm?

get to caltex at heatcote around 12.30-12.40pm

^ this is some indication of the time to be at heatcote for those meeting us there.. cheers

I've decided to come say hi to everyone so I'll be at caltex at 12.30. :D

guys just to confirm

the heathcote caltex is the one just before the M5 bridge on heathcode road?? if so, wat time roughly do you think you will reach this destination?

Edited by Alien

No, Heathcote Caltex is on Princes Highway, Heathcote...it is one km after the Heathcote Rd intesection (where the cruise cars will be coming from) and a before the start of the Sydney-Wollongong freeway at Waterfall.

^ yup this is the last petrol pump!!!

its in the 50 zone!!

So guys drive at 50kms, coz theres always cops there checking speeds..

I reckon they might reach heatcote about 12.30??

So come to heatcote about 12.30 or so..

slim is gonna msg when they leave KK!!




  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...