Jump to content
SAU Community

Recommended Posts

hehehe... thats an awesome first attempt though :D getting the 60fts down is the hardest thing i reckon! i usually range from 1.8 (best run) to 2.2... i dread going back out there cause i'll be back to square 1 :D

i do want to know 2rismos technique :D all i remember doing it slipping the clutch a lil then all hell breaks loose! lol!

Link to comment
https://www.sau.com.au/forums/topic/175434-wsid-117/page/7/#findComment-3240171
Share on other sites

  • Replies 157
  • Created
  • Last Reply

Top Posters In This Topic

Lolz i was in ONE of the 3-4 of the White R33 Gts25t that night with GTR32 rims up front and 300zx (z32) rims on the rear and the BIG white HKS sticker across the windscreen.

you should of done the burnout, still helps on street rubber just no need to do a monster SMOKEY one. (cough) but seems to work for Moanie on her street rubber(cough) sub 2.0 60ft on 225 federals ey.

Link to comment
https://www.sau.com.au/forums/topic/175434-wsid-117/page/7/#findComment-3240230
Share on other sites

Lolz i was in ONE of the 3-4 of the White R33 Gts25t that night with GTR32 rims up front and 300zx (z32) rims on the rear and the BIG white HKS sticker across the windscreen.

you should of done the burnout, still helps on street rubber just no need to do a monster SMOKEY one. (cough) but seems to work for Moanie on her street rubber(cough) sub 2.0 60ft on 225 federals ey.

lol!!! for me its not so much the warm tyres as its for the smoke show.. think after all the stalls and bad attempts, i revel in the fact that i can do a semi decent one :laugh:

I miss my sig :domokun: what happened to it :(

Link to comment
https://www.sau.com.au/forums/topic/175434-wsid-117/page/7/#findComment-3240316
Share on other sites

yeah the silver one was mine. i saw a few white 33s there but didnt get the chance to talk. which car were you in?

it makes a bit over 250kw on the dyno so i was expecting much better times. obviously something wrong with my technique.

tyres are bridgestone s03n 255/17 at the rear. i lowered them to 24psi but did not do any burnouts been told they(burnouts) are ineffective with street tyres.

ive tried a normal take off which was my second run, launched with 2500rpm (as what Ben told me to try) it bogged down intially then as soon as it hits 4000-4500rpm (full boost) wheel spin began again until second gear :laugh:

rubbish.smoke thosse tyres up.the tracks coating reacts to a tyre's heat.

i went half a second quicker after i smoked the tyres good.learn how to do a burnout starting in 2nd gear.it wont break anything.just dont go dumping it like you would in 1st gear.prolong the burnout.

you should be able to get much better grip off the line.but another thing.dont just dump it.

if you have a dyno sheet have a look at where the torque of the engine kicks in and or when boost starts to ramp on hard.launch just below that so at least the car is in motion when your power really starts to kick in and you should feel it give you a harder shove in the seat than you have previously experienced because your not wheelspining your tyres are gripping.hopefully :domokun:

and if you can get you head arround to slipping the clutch and feeding the acc on the launch to reduce wheelspin thatd be the way to go also.you will find less wheelspin and faster times.

and get quick as u can.smooth gear changes.

Link to comment
https://www.sau.com.au/forums/topic/175434-wsid-117/page/7/#findComment-3240453
Share on other sites

Assume most of you guys are using drag radials? If so, what tyre pressure are you running?

Drop them down to 13-15psi if you're not doing so already. Add in a decent burnout (2nd gear) and launch the car by slipping the clutch from 5000-5500rpm (2rismo assured me I wouldn't break anything by doing this and I'm happy to say I haven't done so yet :D ) and you should see an easy 1.8** 60' time or better.

Takes a bit of practise and I've stuffed it up enough times to know, but when done right, there's nothing stopping you from dropping all the way to 1.6** 60'.

Save a tenth at the 60' mark and you should drop at least 2 tenths off your ET :)

Link to comment
https://www.sau.com.au/forums/topic/175434-wsid-117/page/7/#findComment-3244390
Share on other sites

GooD luck CHris! remember:

-remove spare tyre+tools/jack

-1/4 tank of fuel

-lower tyre pressure to 20-25psi

-NICE BIG BURNOUT FOR MOANIE!

-DRIVE IT LIKE YOU STOLE IT!<as 2rismo would say>

ooh and skip dinner too for less weight :)

Link to comment
https://www.sau.com.au/forums/topic/175434-wsid-117/page/7/#findComment-3249168
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...