Jump to content
SAU Community

Recommended Posts

Hey Guys

for people that havent been before, the LVMA is a Large Vehicle Maneuvering Area. Its a big concrete area, with a small hillclimb type area leading up to it

there will be 3 timed motorkana events running simultaneously, and its an awesome day.

here are the details

DATE: SATURDAY 8th SEPTEMBER 2007

TIME: 8AM-12PM (4 hours)

COST: $90 each

CONDITIONS: 90 dB noise limit and no drifting

i will also need 2 volunteers to time 2 of the events, there will be a free lunch in it for them :D

will be accepting payments now, payment is the only way to secure a spot ;)

pm me for bank details

1. John (OCZ-iR/awdrive)________________________________GTiR________PAID

2. Cameron (AEVO3)__________________________________EVO III

3. Ryan (Rubna)________________________________________GTiR________PAID

4. Ramsay (Ramrod)_____________________________HSV Clubsport

5. Terry (WOT)_______________________________________Evo IX________PAID

6. Simon (Willy)_______________________________________GTiR_________PAID

7. Eug (Eug)______________________________________Skyline___________PAID

8. Clint (RSEVO3)__________________________________Evo III RS________PAID

9. V (V)__________________________________________S14 200sx________PAID

10. Arno (Arriegtir)_____________________________________GTiR________PAID

11. Stefan (Luimsiada)______________________________Evo VI TME_______PAID

12. Mark (*WRC*)_____________________________________Evo IX________PAID

13. Nigel (Evo Makinen)_____________________________Evo VI TME_______PAID

14. James (James)_________________________________R33 Skyline_______PAID

15. JLNewton (jlnewton)_____________________________R33 Skyline_______PAID

16. Glenn (Genesis)_________________________Integra DC2 Type R________PAID

17. Rohan (EVOLVD)__________________________________EVO 6.5________PAID

18.

hope to see a few skylines there

heres a few pics of the last one

post-28275-1184200885_thumb.jpg

post-28275-1184200903_thumb.jpg

post-28275-1184200919_thumb.jpg

Edited by EvoJohnny

well its mainly gtiroz and evolution oz, but a few skylines australia guys have been as well

i usually like to organise a couple a year, my car has been off the road for a couple of months so thats postponed things for abit

pm me for bank details :)

Edited by EvoJohnny
  • 2 weeks later...
  • 3 weeks later...

i'm out. folks are visiting and of ALL days, they picked the 8th to arrive :)

i will be selling my spot to Warwick (username is 'Lazy_Bastard'). Have sent you a PM about it.

hope that you will be arranging another event like this soon in the future :P

  • 2 weeks later...
  • 2 weeks later...

Hey mate shame i didnt get to meet you, hope your recovering, im keen to take part in and that are held in the future, car should be quieter by then, was good fun jusdt being a spectator.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...