Jump to content
SAU Community

Recommended Posts

About 6 months or so ago i put a high flow 'metal cat (brand name) ' on my r34. After a while i lost performance and after talking with my tuner we found that catalytic converter had collapsed. Seemed a bit strange since metal cat are supposed to be a pretty good brand. So we threw another one in and a couple of months later, same deal. We pulled it out and my tuner contacted the dealer and got a new one from a different batch (dealer seemed to think they might have had a problem batch).

This one was a lot better however it is now starting to show the same symptoms as before.

-blows black smoke as the turbo comes on and throughout most of the rev range there after. Leaves black dots on the rear of my car.

Black smoke is usually a sign that the tune is far too rich but my tuner assures me that is not the case, though the a/f ratio does dip just below 12 for a few hundred revs. One of his ideas is that the exhaust stream is too hot for the cat, which doesn't make too much sense either since i'm only running 14 psi and 250 rwkw (after fresh tune). Another mechanic told me that my silencer is restricting the exhaust too much and could also be doing something there (3.5 inch turbo back exhaust, silencer takes it to about 2-2.5 inch at muffler).

I want to take it to 300 rwkw soon but there's no point until i get this issue dealt with. If anyone has gone through this before or has any idea what's going on your help would be greatly appreciated.

Car:

R34 gt-t

3.5" turbo back exhaust

metalcat hi-flow cat

microtech ecu

600hp turbo (was doing this before turbo install as well however)

650cc sard injectors (as with turbo, was a problem before injector install)

pod filter

600*300*75 hybrid intercooler

running 250rwkw at 14 psi boost

Link to comment
https://www.sau.com.au/forums/topic/176428-collapsed-metalcat/
Share on other sites

  • Replies 52
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Another mechanic told me that my silencer is restricting the exhaust too much and could also be doing something there (3.5 inch turbo back exhaust, silencer takes it to about 2-2.5 inch at muffler).

Which is it, 2 inches would be a massive restriction, have you considered fitting an Exhaust temp gauge. If the tuner has to severly retard the timing to prevent detonation, then the EGT's can go through the roof. This would make sense, as the gtt's are renown for having to run low timing to compensate for their different combustion chamber design, and higher comp ratio

How close is the cat to the turbo, could try moving it back a bit.

Edited by Adriano

didn't look like it melted or anything. Just seemed like the walls of the honeycomb structure collapsed on themselves. The inlet to it wasn't too bad but the outlet side all collapsed to the center. My tuner seems to think the black smoke is the cat disintegrating as you say. But being on the third one now and it looks like it's doing it again seems strange.

that's the point though. I have received the last two free of charge thx to my tuner, but replacing the cat every three months isn't something i want to be doing. As for being a crappy china cat, if you know of a better brand i'd be happy to hear about it, but as far as i know metal cats are supposed to be the beez neez in australia.

As for temperature collapse, i find it hard to believe since my tuner has them in most of the cars he tunes (some with 400 rwkw+) and I'm the only one with these issues. I'm not rejecting the theory completely and i appreciate the replies but it just seems very weird that the higher power cars don't suffer the same fate.

I'll get the silencer taken out soon and free up the exhaust a bit more and see if that helps i guess.

Any more ideas are still welcome as the issue is frustrating me pretty bad atm.

my mate's rx2 had a metal cat fitted, colapsed on after about 5-10 drives of the car, blocked his exhaust system up and forced the external gate to open causing boost issue's, my car has identical symptoms to yours although alost less power and rb20, we both share the all and mighty *metal cat*...

it seems these cylindrical cats just kinda fall apart. a busted cat will not make clouds of black smoke under power. i can honestly say its because of the tune.

100 bucks says if you put a standard ecu in it wont do it. etc etc.

its basicly trying to burn off all th unburnt fuel and getting hot for it. ie.. if your crusing on the freeway at 100k for 20 mins the cat shouldnt be red hot. but i rekon yours will be. like my one till i got a "decant" tune.

might i suggest taking out the silencer? i didnt have the same prob as you. Stock standard i was on 154awkw. with pods, dumps/front pipe, cat and full 3" exhaust i was on 120awkw with silencer. after taking it out i jumped to 174awkw. silencers suck. it could be putting too much back pressure and keeping the heat in thus cooking the cat. my 2c.

Catalytic converters dont fail from the back of the car the usually always implode in the middle on the trubo side not the muffler side. I would remove the silencer asap. This definately shouldn't be a warrantable item either!

Note: It's most likely the retarded ignition event killing the cat - what timing number are you running.

my guess is the restriction from the muffler as i have seen the same sort of thing ( massive discolouration on the cat body ) on other restricted exhaust systems . to be honest the size your silencer drops down to is insane and your mechanic should have removed it before performing the other performance work on your car .

kermit

Kermit Engineering

no it doesnt.

if you car is tuned well it should smell like new carpet.

and the cat colapses from the rear when to much fuel is going thru it. as it burnes hotter at the back. if it colapses at the front its just got to hot or a blockage. hence why the temp sensor is in the rear of the cat on 32/33's

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • I forgot about my shiny new plates!
    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
×
×
  • Create New...