Jump to content
SAU Community

Recommended Posts

RB25 tappet covers $100

14072007109.jpg

GReddy Profec B Spec 2 boost controller $300 - SOLD

14072007117.jpg

6Boost inlet manifold $350

24022007035.jpg

Turbo similar to gt3037 58ml front wheel .86 rear internally gated 550 hp with standard manifold and dump pipe $1250 neg

24022007036.jpg

24022007037.jpg

24022007038.jpg

Standard Cluster Series 1 $100

24022007039.jpg

Standard Blinkers $20

24022007040.jpg

intercooler, piping, intake, pod filter and catch can $500

IMG_0679.JPG

Also have standard R33 Interior from S1 front and back seats, 4 door trims. no pics yet. $350

Can post some items. All items located in Wollongong NSW.

PH Mick: 0411447639

Edited by MI51LE
interested in the plenum, pics on car, what sort of gains, what throttle body fits it etc etc

hey i have never used the plenum so i couldnt tell you any gains, i bolts straight up to the bottom half of the standard manifold

and it uses a xf throttle body

PM SENT

What is the actual brand and model of the turbo?

How many Km's have you put on it?

How much boost has been run through it?

Any shaft play or other problems?

What is the actual brand and model of the turbo?

How many Km's have you put on it?

How much boost has been run through it?

Any shaft play or other problems?

the turbo is pretty much sold

its a garrett not sure on the model

its done about 20000k's i had it checked out today at turbologic in wollongong and was told its in good working condition

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...