Jump to content
SAU Community

Recommended Posts

/hijack

mine is playing up as well, it will only lock with the key and is sometimes hard to get to lock even with the key. this started soon after me slamming the door really hard... (women)

any ideas on how to fix?

Had this same problem a few weeks back, turned out the "gears" in the locking mechanism were full of gunk inside the door. I cleaned it up, made sure it was well lubricated with some oil and then put it all back together. Haven't had a problem since, hope it helps :blink:

either that, or check inside where the lock is in the actual car frame, see if its still connected;

when i had my alarm installed, the passenger side would lock. this was due to the locking bit where the clip on the door inserts into to lock the car.. in mine, it was disconnected/broken.. fixed it up with duct tape :blink: before i can get a new one(like 5 bucks if that off a wrecker)

mine was doing the same thing...thought it was a dead actuator so i gave the spare i had to my installer...he gave it back to me when i picked the car up and said it was a crushed wire that came from the car into the door...ran a new wire and all fixed :blink:

  • 3 weeks later...

same problem, only on the passengers side, and the door is locked and won't unlock, it appears something in the solenoid is jammed and is preventing the actual door opening mechanism from working >_< f**k it's pissing me off, i've been playing with it all morning, can't get the sucker to open.. any tips?

i had Doug from Eastside Installs come around yesterday to have a quick look at my alarm as i said above, i have the same problem...

it was easy to fix, just a wire in the door that had gone bust, split by the door... easy fix... :D hope this helps?

great success! i didn't take any photo's but if you've ever had the lock mechanism out before it's not hard to picture..

there are 2 screws that hold the solenoid onto the lock mechanism, and another screw that was missing (presumably come undone and fallen out some time ago) that held the solenoid to the frame of the door.

over time it appears that the plastic bit of the solenoid that pivots the door lock up and down had been flexing against itself and somehow eventually come out of the door lock mechanism..

effectivly this jammed the door lock from unlocking, the only way i found to overcome it was to use a long flathead screw driver with a thin blade to wedge inbetween where the two attach each other and then rotate centrifigully, flexxing the solenoid away from lock mechanism and allowing the door to unlock :huh:

works a charm once you sit down and take your time figuring out how it all works, which is pretty hard when the fken door won't open and the only way you can get inside the door is to flex the interior trim :S

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
×
×
  • Create New...