Jump to content
SAU Community

Recommended Posts

BMW 318is 2 Door Coupe

Manual 4cyl

*CHEAP*

Hey guys I am selling my 318is BMW 2 door coupe. Immaculate inside and out, Always garaged, Its manual, Its got a sports exhaust, Tinted Windows, Proffesionly Lowered, Comes with a Pioneer cd headunit and a pioneer cd stacker. Beautiful Car to drive, This car does turn alot of heads. The car has done about 150xxxks. Comes with 10 months reg. If you have any more questions about the car please ask..REGRETFUL SALE DUE TO LOSS OF LISENCE !

WILL CONSIDER OR A TRADE !!

CONTACT 0421714196 Rabz.

11.jpg

33.jpg

22.jpg

Asking Price: $14.000

Edited by YUCUT
Link to comment
https://www.sau.com.au/forums/topic/176586-1995-bmw-2-door-coupe-swap/
Share on other sites

whats your location, couldnt really make it out from number plate

would you be interested in a custom headturning nissan pintara trx

all i have is $5000 to add on top

you can keep any car audio in the car.

heres more info on my car

http://www.carsales.com.au/used-cars/priva...e|1&trecs=2

Edited by gach2
whats your location, couldnt really make it out from number plate

would you be interested in a custom headturning nissan pintara trx

all i have is $5000 to add on top

you can keep any car audio in the car.

heres more info on my car

http://www.carsales.com.au/used-cars/priva...e|1&trecs=2

thanks anyways bro.. Its not my type of car

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...