Jump to content
SAU Community

Recommended Posts

Whoops, my bad, I paid $34, not $17 LOL.. .just double.

^ But that's what mine looked like when I took it off the other month too, must be a 33 thing, blowing out 1/4 of the gasket

rush: Mine sounded like someone farting in a tin can with that much missing :)

Whoops, my bad, I paid $34, not $17 LOL.. .just double.

^ But that's what mine looked like when I took it off the other month too, must be a 33 thing, blowing out 1/4 of the gasket

rush: Mine sounded like someone farting in a tin can with that much missing :domokun:

Haha no worries man, i read other forums and its a common problem on 33z for the gaskets to go apparently, mine has a faint tick (mainly hear in carparks and next to buildings from under the car) dont know which gasket it is tho. Ive heard ppl saying about a gasket and stud kit, does anyone know what they are worth and would it be easy enough to do myself?

Sorry to jump in ur thread Ryan

no problem mate....i did have that slight ticking noise you speak of rushy. It eventually in around 5 minutes got louder and louder. eventually sounded like an external gate on full song...hehe. the dump pipe is also a common one to slightly leak and give off this ticking noise. I owned another rb25det before this one for 5 years.....never had this problem before and that motor wasn't treated with any respect.

Edited by Ryanrb25

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, this is probably where a wiring diagram and a multimeter come into play.
    • I can say to anyone thats doing this; having done a number of R clusters; just be careful if its an unknown cluster.  It takes a bit of force to pull up; but if it feels excessive then its probably stuck. I've had this and pulled the entire hair spring out; and I can tell you; its not easy getting the correct spring replacement with the correct inner diameter and winding. In my case someone had used some sort of adhesive to stick it to the spindle and it pulled the whole spindle out; which the force seperated the hairspring from the spindal and caused it to deform.  You may have to clean it (IPA); or in my case if i'd known i should have used some sort of solvent on it.  Also check out Cruizin Central on eBay. He does all sorts of dials; and you can email him with any custom designs you want. So if you want like certain logos etc...he'll send you a mock of what it will look like then you accept the order and he'll take care of the rest. Fantastic dials and he can do basically any design you want. 
    • Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
    • Ive converted a few clusters for the R33 with 320km/h dials. On the back there are some pads which can be bridged or unbridged (using solder or wick braid) to calibrate it. There is one bridge which is for MPH <> KPH; and there are combinations of bridges to offset it. There is probably a diagram  For example; this is my conversion for a 180km/h dial to a 320km/h dial (I put custom GT-R dials on it with the GTS25t layout) If you have J2 soldered (assuming the S clusters have a similar config to the R clusters); you may need to remove that solder
    • Back on topic 😉, these are some of the notable pages from the booklets that are supplied with each weekly parts update. I never knew the BNR32 test mule car had an S13 Silvia front end... *Edit: On closer inspection the test car still had the R32 body, but only the front end had Silvia panels etc.
×
×
  • Create New...