Jump to content
SAU Community

Recommended Posts

hi guys

on the weekend i did a DIY on my r34 gtt stock bov

we cut a coke can into the shape of the BOV as a gasket to block off airflow causing it to flutter but now it is back firing pritty regularly

y is it back firing so much ?

and how much damage am i causing to the turbo?

thank u =)

Edited by skylinesrus
Link to comment
https://www.sau.com.au/forums/topic/176614-flutter/
Share on other sites

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

hi guys

on the weekend i did a DIY on my r34 gtt stock bov

we cut a coke can into the shape of the BOV as a gasket to block off airflow causing it to flutter but now it is back firing pritty regularly

y is it back firing so much ?

and how much damage am i causing to the turbo?

thank u =)

your car will also stall.

I did the coke can thing and undid it. Its crap. Get a HKS SSQV if you want flutter.

Link to comment
https://www.sau.com.au/forums/topic/176614-flutter/#findComment-3230177
Share on other sites

The afm is expecting air (from plum back bov) to be returned to the air flow, so when you stop that air being plummed back into the air flow the air flow metre doesnt know this and just assumes everything is normal, hence thinking there is more air there than there really is, therefore keeping the same amount of fuel for less air, causing it to run rich. hope that made sence

Link to comment
https://www.sau.com.au/forums/topic/176614-flutter/#findComment-3230202
Share on other sites

The afm is expecting air (from plum back bov) to be returned to the air flow, so when you stop that air being plummed back into the air flow the air flow metre doesnt know this and just assumes everything is normal, hence thinking there is more air there than there really is, therefore keeping the same amount of fuel for less air, causing it to run rich. hope that made sence

So if u put the afm in the cooler piping do you rekkin it would run beta?

Link to comment
https://www.sau.com.au/forums/topic/176614-flutter/#findComment-3230737
Share on other sites

not too sure but the thing is...people have done this but the AFM isn't designed to be placed under pressure, its just plastic, and excess heat to this plastic can cause it to become brital. The afm relies on an accurate reading of resistance measured by a very thin wire. Any excess heat to this could cause improper readings, hence different air/fuel ratio....probably wouldnt be f**k all but there's no point just for a flutter and bad economy.

Link to comment
https://www.sau.com.au/forums/topic/176614-flutter/#findComment-3230770
Share on other sites

LOL

it works... but wouldn't recommend it on a r33 with the ceramic wheels..

blew mine out my exaust pipe and also straight into the intercooler..

i don't see any issue with a steel wheel type turbo

edit: i have fixed this up cos people can't seem to understand wtf i was saying...

Link to comment
https://www.sau.com.au/forums/topic/176614-flutter/#findComment-3231400
Share on other sites

LOL

it works... but wouldn't recommend it on a r33 with the ceramic wheels..

blew mine out my exaust pipe and straight into the intercooler..

i don't see any issue with a steel wheel type turbo

Err how is that possible? Is your exhaust connected to your intercooler? :P

Link to comment
https://www.sau.com.au/forums/topic/176614-flutter/#findComment-3231517
Share on other sites

LOL

it works... but wouldn't recommend it on a r33 with the ceramic wheels..

blew mine out my exaust pipe and straight into the intercooler..

i don't see any issue with a steel wheel type turbo

:laughing-smiley-014:

Luckily it didn't go the other way and end up in your sump hey? or even worse, in the flux capacitor.

Link to comment
https://www.sau.com.au/forums/topic/176614-flutter/#findComment-3231575
Share on other sites

aah.. school holidays :P

if and I stress IF .. your serious about this make sure your aware of the possible damage it might do

also if you REALLY want to do this .. least give the 34 a bit of respect and cut a bit of 3mm Ally plate and paint it black .

on a LOT of cars you will get flutter if you back off on low revs -

at full throttle the BOV is designed to stop air " ramming up against " the throttle body and traveling back past the turbo wheel

Link to comment
https://www.sau.com.au/forums/topic/176614-flutter/#findComment-3231590
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • This is aem disk setting in aem tuner and still 180 dgree off or ignition on exhaust cycle is it from cas it self as cas seems wouldn’t fit in cam shaft if wrong position and wiring been verified any ideas 
    • Oh yeah that would work excellent. Should be the same diff housing & everything. Shoot me a text or call me 260-750-2246 -Cody 
    • Oh right, I didn't realise it was your car. Please do! Makes me feel better about mine. I also have a big scrape on the front left bumper where someone presumably used the wall to guide the car into a parking spot  But somehow all the funds go towards mechanical things and the cosmetics stay forever unfinished... Interesting, I don't think I have seen it before. But after seeing @PranK's rusty roofline on the BMW I'd probably leave it alone. Wouldn't want water to get in there.
    • Thanks mate, thought you might know the answer.     
    • Infiniti US are teasing a manual Q50 as a way to refresh a (very old) model. https://torquecafe.com/manual-performance-sedans-arent-dead-yet/ Can't be too technically difficult given the Z has the same motor with a manual gearbox......here's hoping there is a JDM version we can import here, that would save me a world of headaches
×
×
  • Create New...