Jump to content
SAU Community

Very Neat R32 Subbie Box 12" Sold

femno
 Share

Recommended Posts

180sxdrifterj Community Regular

180sxdrifterj

Posted
Posted

hey dude im really interested.

my current box doesnt really fit. its a brand new cadence ported box for a 12 inch sub.

would you be interested to swap plus some cash your way?

femno Grand Master

femno

Posted
  • Author
Posted
hey dude im really interested.

my current box doesnt really fit. its a brand new cadence ported box for a 12 inch sub.

would you be interested to swap plus some cash your way?

Umm not really interested in a swap, ive already got a small 12inch box in now, reason i dont want this one anymore is so i can easily remove the small box for track days etc.

femno Grand Master

femno

Posted
  • Author
Posted
femno..

Anychance of you measuring it up for us Syd ppl :bunny: (drawing and measurments)

So you can add it in dyi... would be awesome..

Haha yeah mayyybe lol, its pretty complex though, all the curves etc. i dont think it really is even measurable....alot is just random curves to suit the boot interior.

I might measure the box itself tho, it was hard getting the right angle so as it would fit under the attesa and abs computers.....

BUMP! :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • djr81
      R32 update from 1990's spec.

      By djr81 · Posted

      So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...