Jump to content
SAU Community

Recommended Posts

But what i dont understand is wasn't the r33 always illegal to drive on p's?

but now the fine is over 1k

yeah all imports need compliance man. check for a pink compliance plate too...(but i think thats only if its less than 10 years old - im sure though)

the pink/purple ones are for cars imported under the new sevs scheme, so imported in the last few years

OKay I know this sounds really dumb but series 2's still need to be compliance yeah?? I cant see a compliance plate anywhere under the hood of this thing there normally green and sat somewhere either on the strut top or firewall yeah? Could be why it was so cheap...

There shouild be a pink compliance plate on top of the strut tower in the engine bay - mine is on the drivers side. Thats damn cheap still for a series 2 with 90, 0000 km's but then again if it still hasn't been complioed and road worthied then it might all eventually start to add up to the price of an auto s2. I would imagine an auto s2 would be around 15 or so - fully complied and rwc or course... And the thing about road worthy is you never really know how much its gonna cost to get one - as there always little things you dont factor for.

Just to add the car still talks to me in japanse has like a japanes rego sticker on the windscreen and has what looks liek an aussie vin number printed next to the strut tower but theres not compliance plate??

If there is a plate with the "aus" vin on the strut tower or engraved on the strut tower then this car has been brought in under the personal import scheme. No compliance plate required. My mates R32 is the same...... he has a little plate pop riveted to the drivers side strut. Unless Vic has different rules??? I thought it was Australia wide though...

Has the car been previously registered in oz? If not, did they supply engineers papers/mod plate for first rego? The car only needs to have a few things taken care of and signed off on by an engineer if brought in under the 12mth personal scheme. Seatbelts, intrusion bars, etc

I think you'll find that regardless of HOW a car is bought in to the county it is still required to be complied to Australian Design Rules. There should be a compliance plate on all cars. There was a hell of a lot of bad stuff going on before the introduction of the RAWS/SEVS scheme. It was introduced to stamp out a lot of the corruption and back yard scammers and to monitor the workshops who were eligible to comply these vehicles.

I can tell you this for a fact as my previous R33 was brought in and was done under dodgy compliance. The car was a repairable write off and I bought the wreck back an sold it. The new owner bought the car as was and fixed it, when he went to register it they told him that the car was not complied (I was VERY clear when selling the wreck, he didn't seem to care). If you try to register a car with no compliance plate you're not going to have a hope in hell that's the bottom line as far as I'm aware though I stand to be corrected :)

If you try to register a car with no compliance plate you're not going to have a hope in hell that's the bottom line as far as I'm aware though I stand to be corrected :)

Yep pretty much. It might have been a 'bargain' because it's unable to be registered for some reason or another, and it wouldn't have been the first (or last) time someone's done this (sold a car which can't be registered to someone who wasn't aware).

has what looks liek an aussie vin number printed next to the strut tower but theres not compliance plate??

Best bet is to contact DOTARS Vehicle Imports Enquiry Line (1800 815 272) or VicRoads, confirm your mate is the current owner of the car, give them the VIN details and ask about the status of the car. They should be able to tell you whether it's been previously registered / imported for road use, or if it can be in the future.

Private imports are "complied" differently, as are cars older than 12/88 which are eligable for import under the "15 year" rulings.

It may have changed since I brought my S13 in under the private import scheme, Il ask the compliancer next door. When mine was done Green (Pink now) compliance plates are only issued to low volume grey imports, not private nor "15 year" imports. They are issued a VIN and are registerable with an engineers certificate indicating that the requirements have been met for registration.

Mine was around 6 years ago... my mates 32 was 3 years ago. The engineers certificates are not required to be kept in the car etc as per ones for modifications, they are held at the RTA.

Stop your complaining about pricing,

Consider when R33 lines starting to show up in Victoria, i picked my old 33 up for $20 and it was cheap LOL. Stock as, only come with a boost gauge lucky it has ABS and that's like back in the day. These days i still see crazy modded up 33 but no ABS, pretty scary unless you're a race driver.

Stop your complaining about pricing,

Consider when R33 lines starting to show up in Victoria, i picked my old 33 up for $20 and it was cheap LOL. Stock as, only come with a boost gauge lucky it has ABS and that's like back in the day. These days i still see crazy modded up 33 but no ABS, pretty scary unless you're a race driver.

:) I dont follow

Update found the compliance plate you wouldnt believe it on the unbder side of the passanger side door..??..??? WTF??? the vin on the compliance plate doesnt match up with that on the strut tower..so im not too sure she takes it to get registered at vicroads today so Ill find out I guess..

The vin on the strut tower I called up vicroads they said it doesnt even exist so im a bit confused..

anyhow car passed roadworthy only thing it needed was the gps screen removed as it blocked the drivers vision..

one thing though it seems to have the advan tri spoke racing rims on them they look like they have a single hub nut and are not like 5-stud or anything... is this just a cap cause if so we havent figured out how to get it off..any hints??

hmmmm hopefully VIC rds can clear it up... although it doesn't sound promising. Did you enquire on the compliance plate details? Hopefully they are all above board.

Regarding the wheels the centre cap will screw off..... wheel nuts are hiding underneath.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...