Jump to content
SAU Community

Recommended Posts

  • Replies 41
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

nah, it's just more convenient. no passengers allowed on track anyway, plus with passenger seat out my race box fits neatly in the space. i just put it in after track use. takes about 3 mins tops.

ahh cool nice...

Thanks Richard!

I'll return the supercheap one on the weekend or thursday!

Guys: Postage on that firstaids side is "'$16.50" for 1 and when I put in quantity as 2 it's the same :(

Maybe I could email them and ask for a group buy?

any 1kg extinguisher is not up to the task if ur car is on fire its only design to reduce the initial fire before assistance arrives. if ur driving till the point of overheating/fire (this is why u look at your gauges) or havent done the checks before a tack day is more important than anything else. as far as i know many guys dont even have heatshield's on their manifold/turbo/dump etc etc when those are the biggest fire hazard.

its the same chemical compressed to the required pressure and 1 valve. all the same shit if u ask me.

yes spend the extra $20 for peace of mind i can understand, but when it comes from supercheap, they wouldnt be allowed to sell it if IT didnt met standards.

dont be too quick to based price on quality.

where are the bfi ones made anyways?

Edited by philta

there are big differences between so called 1kg extinguishers. some contain only around 500gm of chemical, some contain over double that. they are all rated though.

what's the rating on the supercheap one?

is that one of the foam bomb type extinguishers used in open wheelers? and looks externally activated (or atleast one trigger near the dash)

Yer craved thats correct is a 4kg unit with 6 spray nossles and 2 pull cables one for me in the driverseat and one on the right hand side front wing

Yer craved thats correct is a 4kg unit with 6 spray nossles and 2 pull cables one for me in the driverseat and one on the right hand side front wing

they are an awesome setup, havent seen them used much in sedans though. worth it for sure

they are an awesome setup, havent seen them used much in sedans though. worth it for sure

We have to run to FIA requirements and this is the requirement :-) 3 sprays inside and 3 under the hood. was only about 330$ so not to bad

Richard do you trust those those two small bolts in the bracket to hold the extinguisher back from flying off and getting you in the legs when you have a high speed off/stop?

Not sure what force is generated by a lkg+ mass when you do a Radisich Bathurst 06 into the wall but it's a lot.

They may be more than enough but just thought I'd put the question.

Cheers

Richard do you trust those those two small bolts in the bracket to hold the extinguisher back from flying off and getting you in the legs when you have a high speed off/stop?

Not sure what force is generated by a lkg+ mass when you do a Radisich Bathurst 06 into the wall but it's a lot.

They may be more than enough but just thought I'd put the question.

Cheers

yeah they should be fine. it's not on the drivers side of the car and i have been backwards into the wall before and it didn't budge. for sure they are not massive, but the extinguisher is very light, 2kg total weight. granted I wouldn't want it flying at my head though. not much option to fit any bigger ones sadly. :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
    • To drain the Intake Heat Exchanger, there is a crappy drain plug in front of the driver's side front tyre: You should use the largest headed phillips screwdriver you had, and in my case I needed vice grips on the hose above as the plug was tight (tighter than it needed to be, since it has an o-ring seal).  After you have a tray down and open the drain, open the intake heat exchanger reservoir cap (drivers side one) and you should get a couple of litres of coolant To get to the radiator, you need to remove the plastic engine undertray. It is held on with a series of 10mm headed bolts and some clips. For the radiator, there is another type of crappy drain (kind of like a plastic banjo bolt) and you should attach a length of hose to direct the stream of coolant per this pic (otherwise the coolant hits the rad support and goes everywhere). The drain is on the rear of the radiator on the driver's side and a bit hard to find. Put a big tray or bucket down (5l won't be enough) and slowly unscrew the fitting by hand. You only want to remove it far enough for coolant to flow, it you unscrew it right out the whole fitting and direction pipe will come off and you will get a coolant bath (yum!). Undo the radiator reservoir cap and it should empty about 8l
    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You also need to drain the intake heat exchanger to remove the radiator so you will need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. 2 other tools that really help dealing with coolant lines and spring clamps are Bent Needle Nose pliers Hose pliers Between them they will reduce the frustration (and injury) potential by about 1000% Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
×
×
  • Create New...