Jump to content
SAU Community

Recommended Posts

I'm the same mate. Between my Plazmaman plenum, ETM manifold, numerous other custom alloy and stainless gear I've had done, and an all signing and dancing $20k welder we've recently ordered in at work... I also have one hell of an appreciation of professional welding skills!

Leigh's welding abilities are in another dimension in comparison to my capabilities.

  • Replies 843
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Good and bad. It wasn't bad as far as first meetings go and considering the number of new things to keep track of and the tame settings in the thing, it didn't do too bad at all.

First run out I blew the manifold to BOV line clean off and discovered that the spring in the BOV is about 16.5-17psi. :D It was doing all the boost control for me :) and we pulled every cooler pipe, hose, clamp and fitting off to chase the boost leak that was none of the above.

With that problem sorted (but with round 2 and 3 qualifiers happening in my absence, I had to make do with a random dial-in for first round eliminations. I thought that an 11.anything would do for the day and so dialed in 12.00. It would only hold about 3psi on the foot brake so it drove off the line again (2.006 60') and with the boost leak fixed went 11.87 @ 120.89mph. The speed was back but the launch was atrocious. The transbrake would have to do for grudge runs soon to come.

I forgot to arm the brake for the next pass so we just wont talk about that, okay? :P

Last pass they had time for was ok. Good burnout, everything ready to go, transbrake to about 8psi and when i let go of the button it just went sideways and spun all through first with me peddling it to get it under control. I should have in-car vid of this pass soon. Slow (11.7 @ 120 - 1.9 60').

That was all we had time for today but will be back soon to revise the launch technique. A 1.60 60' time will see the car in the bottom 11's/high 10's no trouble at the same boost etc. Fingers crossed. :)

Good to catch up with a few people today. Thanks to Elmsy, Macka and Yavuz from Unigroup Engineering for their help.

did u take any data logs? if so what did the oil pressure one look like? (i'm using the same pump/line setup as u on a car i'm building)

Oil pressure was about 60psi when oil up to proper operating temp. That's reading the gauge during the run. Haven't seen logs yet.

One of the best parts of the day was cruising with this guy. Car runs 8.30's on slicks and went 8.60's on radials. Made the 45km cruise and drove through the night from Calder Park to be at the event. (They raced the day before!)

24ndv88.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • I forgot about my shiny new plates!
    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
×
×
  • Create New...