Jump to content
SAU Community

Recommended Posts

Hey guys,

My antenna is pretty stuffed, it wont go down as there is a very slight bend in a few of the segments. I tried to bend it straight but it came close to snapping off so I stopped.

Does anyone know of a replacement solution, will a replacement mast (ive seen these available at like Super Cheap) fit? would one of those "universal motorised antennas" fit?

Maybe a wrecker would sell me one, anyone know a likely candidate to have this part?

Thanks

Link to comment
https://www.sau.com.au/forums/topic/17750-r33-series-1-radio-antenna/
Share on other sites

Originally posted by dan_the_man

Try ur nissan Dealer, I forgot to put mine down going through a car wash... Nissan put a new one on

"f***en whoops!!" How much did nissan charge for that?

I have got prices ranging from $95+labour to fit a new mast to $125+labour for a new(secondhand) unit.

I am going to try a repair job myself using a "universal replacement mast/rope" and pull the unit out myself. It looks like something i could handle and might learn something at the cost of $19 part from Supercheap.

If not, ill chalk it up to experience and wear the $100++ cost...

Thanks for the replies

ummm, exactly happened to my R33 antenna.. ALL you have to do is go down to your local JB Hi-Fi and look for any universal electronic antenna should be around the $80 mark. this should fit fine.. it is quite easy to install.. unbolt to old one and bolt the new one in place!..

Originally posted by pushead

ummm, exactly happened to my R33 antenna.. ALL you have to do is go down to your local JB Hi-Fi and look for any universal electronic antenna should be around the $80 mark.  this should fit fine.. it is quite easy to install.. unbolt to old one and bolt the new one in place!..

Sounds like a good idea. What about the cable that runs from the antenna to the radio? Do I have to run a new cable as well, or does it unplug from the motorised antenna end and plug into the new antenna?

This looks like the best plan so far.

Fixed it today. Cost a grand total of $26 in parts from SuperCheap Autos. The "AEPRO universal replacement mast and rope" model number AP12 worked perfectly. Lucky too because it was the only place i could find replacement masts and it was one of the only models they stock.

Bargain!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...