Jump to content
SAU Community

Random Stalling?

nizmo_freek
 Share

Recommended Posts

god's rx Contributor

god's rx

Posted
Posted

my R32 would do this wen i first got it n thats cos the BOV was shite n was openin under extremely small loads, thus lack of air n the car would stall.

f**kin scary wen it stalls at 50-60 and losing power steering tryin to turn...

so +1 for checkin BOV

nizmo_freek Experienced

nizmo_freek

Posted
  • Author
Posted (edited)
changed your sparkies lately. Disconnect the 02 sensor plug and see if it still happens.

Could also be a sticking Auxillary air valve.

Plugs are ngk bcpr6es and have done about 8000kms, will check them over just incase

Will unlpugg 02 sensor tonight and see what happens.

Edited by nizmo_freek
nizmo_freek Experienced

nizmo_freek

Posted
  • Author
Posted
my R32 would do this wen i first got it n thats cos the BOV was shite n was openin under extremely small loads, thus lack of air n the car would stall.

f**kin scary wen it stalls at 50-60 and losing power steering tryin to turn...

so +1 for checkin BOV

The bov is the stock unit, so i dont see how that could cause the problem, unless the spring has somehow lost its tension?

nizmo_freek Experienced

nizmo_freek

Posted
  • Author
Posted

Just unplugged the 02 sensor and went for a drive, no change at all, also after the car stalls then i restart it (let the clutch out while im rolling) ,if i let the car sit there idling while still rolling the revs fluctuate around 1200rpm-1500rpm then after a little while the car will all of a sudden start idling normal at about 700-800rpm which is very strange, seem like a idle valve problem to me, may clean the aac valve on the weekend (have already cleaned it ages ago) and see if i changes anything (somehow i dont think it will), the last resort will be to take it to nissan lol

  • 3 months later...
4drlvr Proficient

4drlvr

Posted
Posted

Hi Guys,

Im having this problem too? So far ive checked the BOV(Tried another pair), checked the cooler piping as well.

Mine seems to do it wen the engine is at running temp. Doesnt do it when its cold. Im running stock comp, pods and a Cooler.

Can be very annoying espically if your to hit the brakes all of a sudden to slow down the car turns off???? Weird....

Have also tried resetting the ecu.

Will Check the TPS and CAS Tonight and see what it does.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • TurboTapin
      Jacks that fit under GTR lips that can reach the subframe?

      By TurboTapin · Posted

      So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • suko
      J50 clock date suddenly reset to January 1

      By suko · Posted

      Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • Dose Pipe Sutututu
      Chris' Toyota Mark ii JZX110

      By Dose Pipe Sutututu · Posted

      I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • MBS206
      Starter motor replacment teeth count.

      By MBS206 · Posted

      I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...