Jump to content
SAU Community

Recommended Posts

i will have a few parts coming off the car over the next week. all parts are in pefect working order, only selling due to power upgrade replacement.

stock turbo - this turbo is a freak, made 300rwhp on 1 bar, no shaft play and no leaks, have dyno sheet to prove power it made......SOLD

stock r33 fuel pump.........SOLD

stock r33 injectors, slight damage on end of one, just were i slipped with teh screw driver, will nto effect how it works at all, only cosmetic!!!!........$80

stock r33 air flow meter.........SOLD

intake part before throttle body.............$20

r33 brake booster with cylinder good condition....... $80

intake for stock turbo, chrome madrel alluminuim bend, pwr silicon hose to fit stock turbo and reducer to fit stock air flow meter.......SOLD

elbow for turbo chromed....SOLD

elbow for turbo polished....$20

3'' stainless dump to suit r33 turbo, was told its hks.......SOLD

stock r33 trubo manifold..........$40

stock manifold heat sheild chromed.......$60

refer to pics below cheers

cheers

post-9180-1185437459_thumb.jpg

post-9180-1185437525_thumb.jpg

post-9180-1185872943_thumb.jpg

post-9180-1185873002_thumb.jpg

post-9180-1185873016_thumb.jpg

post-9180-1185873034_thumb.jpg

post-9180-1185873053_thumb.jpg

post-9180-1185881903_thumb.jpg

post-9180-1185881921_thumb.jpg

post-9180-1185881935_thumb.jpg

post-9180-1186216123_thumb.jpg

post-9180-1186911066_thumb.jpg

post-9180-1186911179_thumb.jpg

Edited by GOR33
Link to comment
https://www.sau.com.au/forums/topic/177942-r33-parts-for-sale/
Share on other sites

Does the intake pipe go to the same position as where the afm would be when using a standard airbox?

Where are you, if out side vic how much for postage?

hmmm not sure about the airbox, it would go very close but cant say yes 100%. it bends around and puts the pod filter behind teh headlight, perfect fit, and sits above teh hole where the stock cooler pipe would be, which dras cool air thrwon up by the front tyre. would ship it for 10 bucks id say

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
×
×
  • Create New...