Jump to content
SAU Community

Recommended Posts

Is anyone on here running these?

I'm currently looking at upgrading as per this post:

http://www.nissansilvia.co.nz/OldWebsite/t...0Binjectors.htm (site off line atm)

And they point out there are a couple of issues with the collers, which are easily overcome.

but just wondering who has used these, and what there thoughts and feelings are on them. Seems to be a good cheap upgrade. Any extra info would be appreciated aswell.

Cheers Guys!

um i was going to do this the hardest thing was trying to find a good cheap set, you also need to change the injector plugs, and rx7 injectors dont have the best spray pattern they just dump fuel. But see how you go.

In terms of fuel spray pattern, the rotory injectors essentially just squirt the fuel in a line.

Speak to red drifter after tuning issues associated with running 13b injectors.

There was a thread a while back about modifying the tip of the stock injectors - removing the tip (forgot the technical term - too tired). It will give you a similar outcome, without the troubles of chopping and changing plugs etc

I run them, they work. Same as blitz 550 injectors if anyone is interested.

You need to trim a lip off the bottom screen and swap the plugs to a standard denso type. You need collars the same as sards. Because the bottom o ring sits low on the injector you need to be very careful installing them in the rail so that you dont pinch it (use petroleum jelly).

Otherwise, they are fine.

Another option you could look at is getting high flows from deatschwerks. Last set of 13b injectors I saw were around $300 or so if I remember properly, whereas deatschwerks only charge around $600 (cant remember exactly how much I paid as it was quite some time ago) and then when you receive their injectors, you send your old stock ones back to them and they give you a rebate. Unless the 13b injectors have been ultrasonically cleaned and flow tested I would go the deatschwerks as the extra pieces + messing around involved in the 13bs, combined with the fact you are getting an old injector that you will have to get cleaned and tested (well not have to, but I would advise it) amounts to a higher cost, higher risk and more effort which IMO isn’t worth the $200 or so you will end up saving (depending on what must be done, purchase price etc). Some people don’t like high flows, but I’ve used them on 3 cars and they have all performed beautifully and drop straight in.

i can get 3 20b injectors for 150, 6 for 300-350, so quite cheap but yes have to get collars and plugs need trim...

am now looking at different alternatives. 98 Legacy twin turbo injectors fit, just need to use an extra O-ring, think they are about 440cc, there is a guy over here using them and getting 300rwkw. I'm also trying to find S15 Spec R (manual) injectors which are 480cc and bolt straight in. but they are hard as crap to get!

Is there anyone else out there using anything interesting as a cheap upgrade? Share....

They are Denso injectors. Spray pattern is actually very good when they are clean. I was previously running S5 550's in my 26/30. You can obtain the injector plugs off most toyota corolla's. As far as fitting in the rail goes, they do fit but the O rings are not interchangeable from your 20/26 injectors, the 20/26's run a slightly fatter O ring which will actually get the rx7 injector stuck in the rail if you use them despite that fact that you can get them on there.

There also hi imp so remove the resistor pack if going into a GTR, and lastly make sure you have them cleaned and flow tested before fitting. Its not uncommon to get maybe 2-3 in a complete set that are seized.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...