Jump to content
SAU Community

Extra fuel for rear cylinders?

Gav

By Gav,
in Engines & Forced Induction

 Share

Recommended Posts

Belly_up Contributor

Belly_up

Posted
Posted

I wouldn't think it would be a set percentage, you'd really need to have provision for EGT sensors in each primary, and monitor all the temps while you adjust the cylinder trim.

I've seen pics of RB26's (may have been one of the big jap drag cars) where the head and/or block is tapped at the back to accept a second coolant hose to better control temperatures. But that may have been due to the RB26 manifold enleanment mentioned above.

Still, if the fundamental problem is heat, and not actually mixtures, then more cooling at the back of the engine may fix the problem, rather than just treating the "symptoms", ie richening the mixtures.

GiJOr33 Experienced

GiJOr33

Posted
Posted

i would have thought that if there was less air getting to the back 2 cylinders (which i presume are no 5 and 6), then they would be running rich, as less air with the same fuel means a richer mixture.... or have i got it all wrong?

Belly_up Contributor

Belly_up

Posted
Posted

GiJOr33, you reasoning is right, however Sydneykid indicated that the airflow in the GTR / GTR Style manifolds was biased *towards* 6 & 5, rather than the other way round, so they run lean.

He also stated that this (air distribution) was not a problem on the 20/25's, so *if* there was going to be a cooling problem at the back of the engine, it would be cooling related, not mixture related, so changing your mixtures would be working against the goal of optimum tuning.

IF testing with EGT probes (not lambda in this case) or similar indicated that there was a problem with cooling, then you would be better off tapping in a coolant line to the back of the block to better distribute the coolant.

And upgrading the water pump and radiator on any high po engine, esp a turbo one, is never a bad idea. Provided your thermostat works properly, then you can't have too much cooling : )

GiJOr33 Experienced

GiJOr33

Posted
Posted

aaaahhhhh.... i was thinking that the first 4 cylinders were using up most of the air in the plenum before it reached the back 2. What must be happening is that the velocity of the air means if flows fast enough so that most of it hits the back of the plenum, meaning cylinder 5 and 6 get the most air and run lean.

Steve Grand Master

Steve

Posted
Posted

If you bow air into a tube from one end and block the other end, then most of the air will be where the tube is blocked, so feeds better into the rear cylinders that the front ones - this would explain the tapering off of the plenum at the rear too. If the plenum was sealed pressure would be equal on all surfaces, but once you open an inlet vavle, the flow dynamics of the entire plenum change - this is why it takes so much time to design any plenum properly, and the flow of each runner must be measured individually - to ensure they are matched as closely as possible.

haveing said that, it would follow that the stock RB20/25 plenum would be biased towards 3 and 4, perhaps they just got the design spot on? From Corky Bells books on forced induction, the plenum design for the RB20/25 is better than a front mounted throttle body.

Interesting subject.

Sydneykid Grand Master

Sydneykid

Posted
Posted

Hi Steve, you asked "As far as cooling for rear cylinders, could it be overheating on 5 and 6 because they are running a bit leaner?"

It's a bit of a circle, 5 & 6 run hotter so they lean out and they lean out so they run hotter. And around it goes.

As for the percentage leaner, I haven't seen any more than 5% and ours is between 2% and 3%. That's at 1.5 bar, at less than 1.3 bar it is hardly anything at all, less than 1%. More important than boost, we are running over 65 lbs of air per minute. That amount of airflow really backs up at the back of the plenum as Steve said in a previous post.

Hope that clarifies

adam 32 Grand Master

adam 32

Posted
Posted

by lifting the rear of the bonnet you would be cooling the rear cylinders more by allowing external airflow.

how effective is it to reduce engine temps from the exterior of an engine (venting the bonnet or raising it) compared to cooling the internals (coolant/fuel) ?

  • 8 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Duncan's V37.......race car?

      By GTSBoy · Posted

      I hope it's actually possible. This is a write off in insurance world.
    • GTSBoy
      Nismo GT Pro LSD configurations

      By GTSBoy · Posted

      Yup. 2-way with shallow ramp angles. Still works.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      That was the first session so not a lot to take from the day. It was low 20s ambient and the coolant had got to 110 (and obviously had some pressure!) so that still needs to be addressed. I haven't downloaded the data yet but will. I had refilled the auto trans with Redline DT6 because it claimed the best viscosity I could find at 100o. It wasn't really long enough to get a good feel for that; while the trans got to 100o in the session it still wasn't shifting crisply as I hoped. I think I'll try a few more sessions before judging. No steering motor overheat but I'd hope not in only 1 session! But finally the suspension; it was night and day over the standard stuff and the car was a couple of seconds quicker on the same crappy tyres, which is a huge difference. I'll stick with that and get some sway bars and a mechanical diff sorted too and see how that all goes together
    • CRSKmD
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By CRSKmD · Posted

      I guess it’s partially a compromise of how my car is used, wanting to be able to switch from drift to grip with track side on-car adjustment. Also partially with the way the knuckles are set there is more static camber but less dynamic camber gain. 
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      OK, so update from the track day on Friday It was a classic "an unfortunate series of events'. There were a few cars around and when i checked my mirror coming out of the fish hook I notice some smoke from the rear of mine. Looked again and it was getting much worse, I figured I'd blown a turbo or something to got off it and pulled off the racing line. However.... since it is a left hairpin into a right kink, I was on the inside of the next corner. There was a car passing me on the left and a big drop off over the ripple strip on the right......and someone had knocked the witch's hat that was on the apex about 1m onto the track. So, between those 3, I decided to mow down the cone and not damage my car/the other car. Right choice, but surprising result.  The car decided the cone was a small pedestrian so it blew the rear bonnet hinges up to protect their head in the upcoming person to car impact....I didn't see that coming and like an airbag deployment it happened super fast. Straight into the pits from there, everything was driving fine but it became clear it was a coolant leak not smoke, it was billowing up onto the windscreen. Onto the trailer and home. I'll do a separate thread about the repair (once I work out what it is ), but the immediate problem was the bonnet wouldn't open because the front was pinched onto the front bar and would not release. Ultimately we unbolted the hinge from the bonnet, pulled it back a little and it released from the front OK. "There's your problem", the top radiator hose had popped off at the radiator.
×
×
  • Create New...