Jump to content
SAU Community

Recommended Posts

The GTR's guards and bonnet are also much lighter than the GTSt gear.

you need to do the grill bonnet and guards bud, all at once

You don't need to change the grille, bonnet and gaurds at once. You can change the bonnet and keep the 'normal' gaurds. If you change the gaurds, chances are, you'll need a new front bar.

The GTR's guards and bonnet are also much lighter than the GTSt gear.

You don't need to change the grille, bonnet and gaurds at once. You can change the bonnet and keep the 'normal' gaurds. If you change the gaurds, chances are, you'll need a new front bar.

if you change the bonnet you WILL need to change the grill ...

Bonnet is different (and the GTR one is alloy)

Guard are different (and the GTR ones are alloy)

Grill is different (GTST has no grill)

Latch is different

Front bumper is different

basically nothing is the same.

Bonnet is different (and the GTR one is alloy)

Guard are different (and the GTR ones are alloy)

Grill is different (GTST has no grill)

Latch is different

Front bumper is different

basically nothing is the same.

:)

all in all, you gotta love skylines......

they look similar, yet are so different when ya get down to the fine details.

lol

mate, gd luck with the what ever your doing

(i cant say any thing new/else as its been stated prior)

Edited by SEX-DR.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The oil pressure sensor for logging, does it happen to be the one that was slowly breaking out of the oil block? If it is,I would be ignoring your logs. You had a leak at the sensor which would mean it can't read accurately. It's a small hole at the sensor, and you had a small hole just before it, meaning you could have lost significant pressure reading.   As for brakes, if it's just fluid getting old, you won't necessarily end up with air sitting in the line. Bleed a shit tonne of fluid through so you effectively replace it and go again. Oh and, pay close attention to the pressure gauge while on track!
    • I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
    • I take it that the knock retard is from bearings tapping a little tune? Thicker oil is a fragile bandaid. You need a much bigger oil cooler and probably the bigger pump being discussed.
×
×
  • Create New...