Jump to content
SAU Community

Recommended Posts

hey all,

i need some advice on making my car higher. i have a 34 4 door and it has been lowered from aftermarket springs. i dont' have the standard springs on the car as i bought the car without.

now heres the story, my cars body is roughly 15 cm from the ground and the lowest point of my exhaust is roughly 7-8 cm off the ground.

i'm getting a bodykit soon and it'll most likely drag the body down to like 8cm. i want my bodykit to be about 10-13 cm from the ground for legal purposes.

i'm pretty tight on budget but may be able to fork something out.

what are your opinions?

Link to comment
https://www.sau.com.au/forums/topic/178387-too-low/
Share on other sites

a really cheap option might be to do what i have done with my R32 to try and raise the suspension and clear the car from defect. Make up, or have made up for you some metal plates that sit on the top hat of the strut over the 2 bolts that go into the tower. Work out how much higher youll need to go, for eg, if you want to raise it by 10mm get a 10mm plate and wack in in there. You might want to consider going longer studs on the top hat than standard as i have done so that you can still safely bolt the struts in.

Im pretty sure this would be a good cheap option for you dude but somebody else with a few more suspension smarts than myself might be able to shed some more light on this for you..

good luck

Link to comment
https://www.sau.com.au/forums/topic/178387-too-low/#findComment-3258538
Share on other sites

thanks for the replies.

i've decided to expand my budget for some aftermarket coilovers with height and damper adjustable settings.

now the new question is, how high can most of the aftermarket coilovers go? would they reach standard height? or can they go just above?

Link to comment
https://www.sau.com.au/forums/topic/178387-too-low/#findComment-3259165
Share on other sites

and the cops go off the lowest point of the car, so in your case the exhaust. so you need to raise it up to 10cm.

If that low point your talking about is beneath the axle, then that doesnt count, look it up on rta they cant get you for having it too low on certain points. just dont rub it in the coppers face or they'll find something else to get you on.

Link to comment
https://www.sau.com.au/forums/topic/178387-too-low/#findComment-3262791
Share on other sites

yeh, well i want to raise the car up so the exhaust would be legal height and when i fit my bodykit on it'll have enough height to clear it also.

right now it sucks because the exhaust scrapes alot and it doesn't sound good (yes i do take things on angles)

Link to comment
https://www.sau.com.au/forums/topic/178387-too-low/#findComment-3263878
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hard to say, just pop the rocker covers off and have a look if you think it's cammed. You probably need to replace the valve cover gasket/half moons anyways.
    • From my youth: GTi-R clutch change is a massive pain. The gearboxes are fragile? But the car is super cool and I want one 😢 
    • Remember this is 1988 tech.
    • Driveline vibration is resolved. I ended up loosening all my engine mount and trans mount bolts, giving it a good shake then retightening everything and it's gone... Let's just say I was surprised that fixed it.  I've been happily driving it around again but unfortunately put zero time into my direct port/constant pressure WMI setup. I'm on vacation next week, so I'll try and finalize it then.  On a different note, I spent all week fuel/ignition mapping 2x 216L V16 engines. Turbo's were burning glycol and we swapped them out for larger units. We also had planned emissions testing on site, so I figured I'd be there the same week to use their instrumentation and massage any emissions issues out if needed. This was a first for me. Fuel management is similar in certain ways to automotive (i.e air density as load variable) but very different in others. It's all PLC based and AFR's are controlled by air and not fuel. They use a control valve between the turbo and air manifold to control pressure which in turn controls AFR's. Due to this, target AFR tables supplied by the OEM are in pressures and not mass which really through me off. They use air pressure vs fuel pressure tables. I also relied on an O2 concentration sensor the emissions team had in the exhaust. Ignition timing was also all over the place and we were losing a fair bit of power. They're now happily sitting at 16-40BTDC depending on load. We were making about 1600kw at 900rpm at 90% load. Engines were running a lot smoother as well.    
    • heh, aint no R32 ever meeting modern targa cage rules unless the driver is veeeery short OP, good luck with the sale, since its already in the land of freedom I'm sure you will find a good buyer.
×
×
  • Create New...