Jump to content
SAU Community

Recommended Posts

Hi,

One of my parkers has died. I had a quick look to see how difficult it would be and it looks like a bitch of a job. There doesn't seem to be anything regarding how to change parkers on the forum...

Has anyone done this before? It's a S1 GTS-T. The side in question is the same side as the turbo...

Link to comment
https://www.sau.com.au/forums/topic/17895-changing-the-parkers-on-an-r33/
Share on other sites

yeah u can do it, but im constantly tinkering with them so i always find it easier to just unbolt the and fiddle here and there. like i had the indicators goin in the parker bulb case for a while, but it was fast flickering (small bulbs) and you couldnt see it, so i changed it back. ive got cut wires here and there hehe

Well, I changed it for the princely sum of $1.50... Undid the power cable and gave it a small twist with the needle nose pliers. Then it just unscrewed :-) Same thing in reverse to put it back. I don't think they'd ever been changed before 'cause there was that much crap and dust in there... It's amazing the things that never have been changed before... My spare tyre is the original japanese one (although it -should- have been replaced), and it's still got it's dye on the tread.. Never been used :-)

  • 8 months later...

Ok, this might be a dumb question but how do you change the parker bulbs in that are in the actual headlights? (not the ones on the corners).

I tried twisting the grey plug under the main circular cap on the back of the headlight but it wouldn't move and I really don't want to get the pliers onto it unless I know that I'm twisting the right thing the right way!

Oh, and yes I know you can't pass a roadworthy with these parker bulbs in.

Ok, after sticking my head under the car today I managed to disconect the -'ve wire that was running to the extra parking lights in all 4 of my headlights.

Couldn't actually pull the bulbs out as the assembly for them (which is located on the bottom of the headlights) is a kinda rubber plug sealed with something that feels like silicon...so it may actually be a custom job.

Tomorrow morning I'll reconnect one side and post pics :-)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...