Jump to content
SAU Community

Recommended Posts

I have a GReddy Oil Cooler kit located BEHIND my Intercooler and in front of my radiator.

Was wondering if it would perform better if i moved it to the side of the bar (it has vents and can get all the ait it needs)

Was speaking to someone at a reputable workshop and they advised that most cars run it behind the intercoolers in the middle as the sides have disrupted air? <-- don't really know what that means but i take it that it doesn't recieve nice flowing air.

So who has their oil coolers on the side or has had them there?

Any temp differences?

If it makes any sense, i have a R34 GTT with a Nismo front bar.

Cheers

Edited by Fujiwara
Link to comment
https://www.sau.com.au/forums/topic/179349-oil-cooler-location/
Share on other sites

Anywhere where it will get maximum airflow without hindering the performance (heating up) of any other cooling device (intercooler, radiator etc.)

If you put it out of the way of the intercooler but in the way of the radiator that would be the best spot without any major modifications imho.

Radiator should be able to cope, if it does cause an issue main way to cool your engine (i have found) isnt additional capacity in the radiator, its raising your bonnet at the back and venting at the back, works like a charm.

Edited by hecticrb25

Hey Dude,

I have just fitted mine to the side.. inside wheel well,i wouldnt put in front of a radiator as although you will be taking heat away from the oil you'll be adding some back into the waer via the radiator.The best position is away from the intercooler and radiator, you can hard mount it when the hoses are long, easiest way for fitment is by removing the headlight and front bar on a R33 it may be the for a 34, good luck with it. cheers

of thats just great...

i can't do this myself cauz i;'ve never taken these things apart.

Nor can i fabricate brackets/mounts to fit on the site.

Have to see what some performance shops will charge me >_<

No doubt an arm and leg

i can't do this myself cauz i;'ve never taken these things apart.

Nows the best time to start! Its just bumpers, some brackets, inner guard liner etc. Get stuck into it, just stick it all back together

Have to see what some performance shops will charge me >_<

Prolly your family's arms and legs as well. Its the labor that kills you. Search this forum for some guides and inspiration. Might not be as hard as you think. Its just large scale Meccano :D

the side duct is the BEST place to put it. you will need to make a vent in the rear of the guard liner though for the air to escape, but once done you now have a much better set-up.

I'd like to mount my oil cooler kit where the stock intercooler used to be and perhaps fabricate an air guide to it. I drive an R34 and will probably do it myself. If i get it done prior to you, I will try to put together a guide.

Edit: On second thoughts, check http://www.skylinesaustralia.com/forums/in...p;hl=oil+cooler

Good guide for an R33 and should translate to R34. Great location too.

before you even bother changing anything, are you actually having any oil temperature related problems ?? i would take a guess that although its not in the most ideal position, it will still be effective enough where it is.

its not a case of finding the best location gives you more power (like a fmic), but rather its purpose is to just regulate oil temps and keep them under control. if its doing that job already, then there isnt any need to move it.

before you even bother changing anything, are you actually having any oil temperature related problems ?? i would take a guess that although its not in the most ideal position, it will still be effective enough where it is.

its not a case of finding the best location gives you more power (like a fmic), but rather its purpose is to just regulate oil temps and keep them under control. if its doing that job already, then there isnt any need to move it.

^^ pricelessly, you'll prolly find the position between i.cooler and radiator is fine.

Hmm...

no problems with cooling or oil temps.

Just thought i'd move it to save trouble later on if it does occur.

But maybe you're right.

I'll keep it there and move it if i have to.

Thanks for the advice guys!

My favourite spot is to have it on the side. There is room on r32s and r33s to run the lines underneath the headlight and put it on the right hand side.

I prefer this, because it has its own dedicated airflow. Also, its neater, because you don't have to run the oil lines either over or under the radiator (messy)

  • 11 months later...

Just a heads up. I fitted a greddy oil cooler and relocator kit to a r32 gtr. Oil cooler between the ac condenser and intercooler. It's a bitch of a job to do. Will never do it again !.

Has anyone else got this set up ?

Have you taken your car to the track and did it keep your oil temperatures down ?

Cos if this setup can't take a track outing once in a while I will not be happy in relocating the mother

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey Dave, welcome aboard! Good to see another soon-to-be Stagea owner here. The wagons are awesome — plenty of space, still got that Skyline DNA, and loads of potential if you’re into mods. Definitely post up pics when you get it, everyone here loves seeing new builds. What model/year are you looking at?
    • See if you can thermal epoxy a heatsink or two onto it?
    • The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
    • So, what else.... Power. I don't know what it is making because I haven't done a post tune dyno run yet; I will when I get a chance. It was 240rwkw dead stock. Conclusion from the day....it does not need a single kw more until I sort some other stuff. It comes on so hard that I could hear the twin N1 turbos on the R32 crying, and I just can't use what it has around a tight track with the current setup. Brakes. They are perfect. Hit them hard all day and they never felt like having an issue; you can see in the video we were making ground on much lighter cars on better tyres under brakes. They are standard (red sport) calipers, standard size discs in DBA5000 2 piece, Winmax pads and Motul RBF600 fluid, all from Matty at Racebrakes Sydney. Keeping in mind the car is more powerful than my R32 and weighs 1780, he clearly knows his shit. Suspension. This is one of the first areas I need to change. It has electronically controlled dampers from factory, but everything is just way too soft for track work even on the hardest setting (it is nice when hustling on country roads though). In particular it rolls into oversteer mid corner and pitches too much under hard braking so it becomes unstable eg in the turn 1 kink I need to brake early, turn through the kink then brake again so I don't pirouette like an AE86. I need to get some decent shocks with matched springs and sway bars ASAP, even if it is just a v1 setup until I work out a proper race/rally setup later. Tyres. I am running Yoko A052 in 235/45/18 all round, because that was what I could get in approximately the right height on wheels I had in the shed (Rays/Nismo 18x8 off the old Leaf actually!). As track tyres they are pretty poor; I note GTSBoy recently posted a porker comparo video including them where they were about the same as AD09.....that is nothing like a top line track tyre. I'll start getting that sorted but realistically I should get proper sized wheels first (likely 9.5 +38 front and 11 +55 at the rear, so a custom order, and I can't rotate them like the R32), then work out what the best tyre option is. BTW on that, Targa Tas had gone to road tyres instead of semi slicks now so that is a whole other world of choices to sort. Diff. This is the other thing that urgently needs to be addressed. It left massive 1s out of the fish hook all day, even when I was trying not too (you can also hear it reving on the video, and see the RPM rising too fast compared to speed in the data). It has an open diff that Infiniti optimistically called a B-LSD for "Brake Limited Slip Diff". It does good straight line standing start 11s but it is woeful on the track. Nismo seem to make a 2 way for it.
×
×
  • Create New...