Jump to content
SAU Community

boost guage

ImPrOvIsE

By ImPrOvIsE,
in Western Australia

 Share

Recommended Posts

adam 32 Grand Master

adam 32

Posted
Posted

i still think despite the age of your car, if the actuator line is in good condition and is getting an accurate pressure reading then boost pressure will always be constant

zanda no i wouldnt stress. youve always got the boost cut at around 12psi (i think) which would prevent and mecanical damage

  • 2 weeks later...
caminperth Grand Master

caminperth

Posted
Posted

hmm.. Suprising because of the mechanical nature of the actuator.

It is my understanding that the mechanical actuator measures the boost level on the compressor side of the turbo and when this level gets to a certain pre-determined point (ie 6 to 7psi for an R33) it then "actuates" or opens the wastegate to keep the boost at that level.

If this is correct, then I fail to see how making the flow in and out (inlet and exhaust) of the turbo will in any way change how this mechanical actuator works. It will still open the wastegate as soon as it sees the set boost level.

The only way I can think that it could possibly produce more boost is if the increase in flow through the turbo is greater than what the wastegate can deal with. Therefore the wastegate is at maximum flow and still more air is flowing due to the increase in size/flow of the inlet and exhaust (predominately the exhaust), producing more boost.

I did not think that the maximum wastegate flow would be so low as to let this happen. I was obviously wrong. Hence I find it suprising.

Always good to find out new stuff. :rolleyes:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I'm actually not sure - I think it was "Stealth Performance" (It really is near impossible to find a FEMALE 1/8BSPT to 1/8NPT male at ALL) but having the thing leveraged on a 90 degree angle on a small aluminium fitting is not too smart. Also in not too smart, I've drilled out the center of the broken fitting so there's maybe 0.00001mm of thread to bite into, so yeah. I may have to get it drilled/tapped/plugged entirely. Given I could conceivably tap a thread/adapter/pressure line in any point in the oil system I suppose it's feasible to run a line to the Nissan Sensor to keep the dash working. Do these exist in AN fittings and the like? Like an AN fitting that has a NPT (or other?) thread as well for putting a sensor in?
    • sonicii
      Anyone running the VQ37VHR with forced induction?

      By sonicii · Posted

      I would agree.  There will be an amount of boost you could run safely with an otherwise factory system, but it would be low enough to not be worth the cost.  And if you are reliving your 20s, you know a 'little bit' was never enough. Personally, if I didn't want to spend the money, then stick with NA bolt-ons, and maybe a tune.
    • Dose Pipe Sutututu
      Mistakes were made, my R34 Story

      By Dose Pipe Sutututu · Posted

      Fuark, at least the motor survived. What brand was the fitting that snapped?
    • GTSBoy
      Anyone running the VQ37VHR with forced induction?

      By GTSBoy · Posted

      Wrong question. There's no point in spending the rather large sum of cash and effort to add turbo, without taking it to the "sensible" limit of the motor itself. If you have to upgrade injectors, etc, then so be it. That is a tiny fraction of what it will cost you to turbo it.
    • GTSBoy
      Starter motor replacment teeth count.

      By GTSBoy · Posted

      Measure voltage at the starter solenoid terminal when the key is at start and it has clicked. If it is really low, then the suspicion falls on the ignition switch (contacts or wiring thereof) as causing a voltage drop instead of sending enough volts to throw the solenoid all the way to engage the starter itself. If it is a decent voltage, then the suspicion is on the solenoid. Might have s horted coil, or might hva dirty contacts. Rip the starter off, dismantle, clean up contacts and inspect winding. It might not be possible to see if there is a short in the winding though. I have a spare starter here that I could measure the resistance of the coil, as a guide to about what it should be, if you need a comparison. <parts hoarder>No you cannot have it.</parts hoarder>
×
×
  • Create New...