Jump to content
SAU Community

Recommended Posts

Hey guys,

Recently my car had started playing up. After seeing that the problem had nothing too do

with the coils, i narrowed it down that cylinder 5 was the one playing up.

After doing a compression test it read too be under 50 which meant either the valve was playing up

or a piston ring had broke.

After i checked my oil i noticed there was non left in there! So i filled around 3 and a half litres at my

cousins place then drove it home. In the morning i checked the oil, and there was no oil left!

So this means that defiently a piston ring is broken?

If so does anyone know anyone or anywhere that supplies a piston ring kit for Rb25det, also with the

conrod bearings and sump gaskit etc.

Thank you!

Samir

Link to comment
https://www.sau.com.au/forums/topic/179976-cylinder-5-no-compression/
Share on other sites

Hey guys,

Recently my car had started playing up. After seeing that the problem had nothing too do

with the coils, i narrowed it down that cylinder 5 was the one playing up.

After doing a compression test it read too be under 50 which meant either the valve was playing up

or a piston ring had broke.

After i checked my oil i noticed there was non left in there! So i filled around 3 and a half litres at my

cousins place then drove it home. In the morning i checked the oil, and there was no oil left!

So this means that defiently a piston ring is broken?

If so does anyone know anyone or anywhere that supplies a piston ring kit for Rb25det, also with the

conrod bearings and sump gaskit etc.

Thank you!

Samir

ouch that doesnt sounds good, but seriosuly something like oil should be checked (the level) atleast once a week.

Was there no oil whats so ever or it just didnt register on the dip stick. Where you still getting oil pressure?

Unless you have a massive oil leak (and if you lost 3.5L in a drive home just by it dropping oil would be EVERYWHERE), its burning or you have massive piston blowby and it filling up your cooler aswell. Is it blowing a shit load of smoke? Any Knocking noises?

I'd say you have either melted/chipped a piston or broken a ring which case your more than likely need new pistons let alone just rings. You probably have damaged your bore aswell and are most likely up for a rebore or hone at the very least.

So pretty much its full rebuild time, ie new pistons, rings, big end and main bearings etc etc (and if you have been driving around with no oil you might have damaged the crank aswell), or get a 2nd rb and drop it in and hope for the best.

Oh man hehe :(

There is still oil pressure, yeah it didn't show on the dipstick.

There is no oil leaking on the ground anywhere

and when i drive no smoke comes out unless i push it a little bit :)

Also no knocking noises.

I hope it's only the rings!

Only on cylinder 5 there is a lack of compression

every other cylinder is fine

Thanks

Samir

Edited by Taxi33
Oh man hehe :P

There is still oil pressure, yeah it didn't show on the dipstick.

There is no oil leaking on the ground anywhere

and when i drive no smoke comes out unless i push it a little bit :(

Also no knocking noises.

I hope it's only the rings!

Only on cylinder 5 there is a lack of compression

every other cylinder is fine

Thanks

Samir

yeah i hope for you its only rings, but regardless i would be giving it a full rebuild while it was out, especially now you know that it had bugger all oil in it. I dont know how hard it would be for you but try and take the intake pipe off that goes to the turbo and see how much oil is in there, your rocker cover ventilation goes to your intake pipe so if there is excessive piston blowby from a busted piston you would expect oil to be filling up in your intake. If you have an oil catch can, you probably would see that its filling up aswell

No idea where all the oil went,

Defiantly not on the ground though when i accelerated a bit hard

smoke came up through the gearbox and white smoke came out

of the exhaust :P this is before i knew it was cylinder 5 playing up

Thanks

Samir

Are you sure you filled the oil into the engine and not the radiator?!?!? cause if it was gone in such a short trip, it wouldve had to be blowing shitload of smoke, and or a big hole in ur sump. also, just incase, check ur intercooler, for oil. you might find it full with oil.

its going to be a bitch to take the piston out from underneath unless you take the gearbox off, take the main crank seal housing, oil pump, oil squirters etc etc and drop the crank.

it will probably be easier to take the head off and just replace the rings and slap it back together if you want to do it on the cheap, but you might as well do the main and big end bearings while its all stripped (it'll only cost you around $140 extra for ACL bearings if you're doing it yourself).

you'll need to check the clearances of the bearings and the bores too, and figure out why only #5 lost compression.

its going to be a bitch to take the piston out from underneath unless you take the gearbox off, take the main crank seal housing, oil pump, oil squirters etc etc and drop the crank.

it will probably be easier to take the head off and just replace the rings and slap it back together if you want to do it on the cheap, but you might as well do the main and big end bearings while its all stripped (it'll only cost you around $140 extra for ACL bearings if you're doing it yourself).

you'll need to check the clearances of the bearings and the bores too, and figure out why only #5 lost compression.

Yeah true,

Though im not too sure if the piston will still be the same.

People are saying that it could be damaged like.. a hole init

or melted so yeah ;)

I think it'll have too be a full rebuild.

Yeah will be doing it all myself, well with my brother/cousin and dad helping me

because they all have a good amount of mechanical knowledge between them.

Going too take it too my brothers work on saturday (hpf) hopefully they'll know whats

up with it and what will need too be done.

Yes.. I'm sure i filled the oil in the correct place. Before i started driving it read full on the dipstick.

The next morning it read empty :(

Thanks

Samir

yeah dude, a melted piston is nasty as hell. look at the pic on my avatar. that was after a nasty little boost spike at WSID. i ran a 14.0 on that run though.

ive got some rb25 pistons here if you're after some.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I can ship Nismo floor mats to you: https://www.oemsoko.co.jp/products/nismo-floor-mats-for-skyline-r33-bcnr33-stagea-wgnc34?_pos=1&_sid=9278c1467&_ss=r  
    • Here's the link: https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6642/misc/G49?frame_no=WGNC34-137122 What you think about it? The same product i found on nengun: https://www.nengun.com/oem/parts/40567/MiPwn5qAMfCfmpxHNDnwn5q9MDAx8J-QiW9sZC1qcC0xMTAtRzQ5LS0wMDE/Floor+Carpet+%2F+Mat+2/0688339eba149c19 Bot i have spoken to 😅 ensured me, that mats are 100% original, oem product. I have my doubts. I also heard what you mentioned, that nengun often offers items that are actual not available... On the other hand mats i found on japanese yahoo or ebay are in poor condition and still quite expensive so i'd rather wait for some better offers. My location - Poland. We literaly don't have ANY market for used Stagea parts so need to search outside Europe.
    • You can’t see much on the other side as the lcd is there I don’t think it’s the same as the m33 beside it as the markings on top is not the same was hoping someone had a good quality photo or if they just happened to have the unit in hand, quickly take the cover off and take a photo to clearly show the marking on top to identify the diode   the unit is currently with an electronics repair shop so I can’t take another photo at the moment hopefully they are smart enough to know if it’s a zener diode or not
    • I'd be very surprised if you can buy new OEM mats. But if you can, I want some too!  Do you have links to the variations you found? Also, where are you located? I found that Nengun is happy to list items to purchase but when you do buy them you'll get an email that it's actually discontinued. As far as I know the variations in floor mats are different colour schemes as well as automatic and manual having a slightly different shape. The automatic ones fit into a manual car without issues, but I think you'd have trouble fitting the other way around. I have photos that show the shape difference if you care. FWIW I bought sets of used floor mats in decent condition at yahoo auctions.
    • Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
×
×
  • Create New...