Jump to content
SAU Community

Is This Okay..

nissan200sx.dk
 Share

Recommended Posts

nissan200sx.dk Community Regular

nissan200sx.dk

Posted
Posted

Hi.

Have a question about me RB25DET s1 engine that im building.

My tourque wrench is one from work, our test department uses it. Its calibrated 2 times a year, and uses a dial gauge built in it. Goes from 0 - 80Nm.

Just tourqed down the main cradle, but now my crank sort of "binds".

When the crank just has been turned around, it will spin free, and only require ~2 N to be turned. (You cant really measure it as it really doesnt move on the dial.) Easy to turn by hand.

When the crank hasnt been turned for a minutte or so it "binds". Will need around ~5 N to get it to spin free again. (On the dial gauge you can only see it move, and then drops back to nothing as the crank begins to turn / frees it self from the "bind")

Is this just oil friction I have to overcome just when turned? or?? Could this be a problem?

Best Regards

Ronni

Link to comment
https://www.sau.com.au/forums/topic/180559-is-this-okay/
Share on other sites
nissan200sx.dk Community Regular

nissan200sx.dk

Posted
  • Author
Posted

The applied force just need to be a little higher to get it to turn over when it has been standing still for a little minutte or so.

After it has begun to turn the applied force to turn it is close to nothing. It turn freely the hole way round. There are no spots were it feels more or less freely to turn.

Link to comment
https://www.sau.com.au/forums/topic/180559-is-this-okay/#findComment-3283101
Share on other sites
nissan200sx.dk Community Regular

nissan200sx.dk

Posted
  • Author
Posted

Have measured both crank and cradle, ordered correct bearings, got the ordered bearings. Mounted with clean surfaces (back side of bearing) and used plenty of motor oil to lubricate.

When it is turning it feels free and top nice. My only concern is what it is that is "holding" it when it hasnt rotated for a minutte or so. What i need to overcome for it to turn.. Could it just be oil friction? Because when using the tourque dial gauge the applied force to get it turning (when i have to overcome what is holding it) is only just the needle moving, only just moving, not even up on the dial...

But when it has just been turned, and then turned again there is nothing holding it. The needle doesnt move to turn it.

Tomorrow i will try with a different tourqe dial gauge. goes from 0 - 8N. Should be apple to see more accuratly.

Link to comment
https://www.sau.com.au/forums/topic/180559-is-this-okay/#findComment-3283150
Share on other sites
SilverECR33 Veteran

SilverECR33

Posted
Posted (edited)

On older engines, it was perfectly fine to use oil, i cannot comment on whether grease would have been better or worse. But I thought your not ment to use grease on ur main cap bearings.

What I can say, (which sounds like your describing), is that when the crank is stopped, its harder to get moving, then once its free its fine. then when u stop, it sort of sticks.

On the last rebuild on my v8. The crank did the same thing. and it was perfectly fine. If your really worried about it, borrow another torque wrench, and retorque it. and see if its the same.

since their is no oil pressure, the bearing oil hole and groove, can only pickup oil from spinning. when you sit still, the oil is pushed back off the bearing into the groove, you have to then spin it to pick up the oil into the hole and groove again.

Thing is, you must still be able to move it buy hand, at the correct torque. if its harder than that. its possibly too tight.

but i would rather a professional post here. as Im a novice. good luck.

Edited by silverbulletR33
Link to comment
https://www.sau.com.au/forums/topic/180559-is-this-okay/#findComment-3283710
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • iain_ST44GA
      M35 VQ25DET starter motor

      By iain_ST44GA · Posted

      Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • Murray_Calavera
      R33 GTR running -9 with no tune

      By Murray_Calavera · Posted

      I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...