Jump to content
SAU Community

Is This Okay..

nissan200sx.dk
 Share

Recommended Posts

nissan200sx.dk Community Regular

nissan200sx.dk

Posted
Posted

Hi.

Have a question about me RB25DET s1 engine that im building.

My tourque wrench is one from work, our test department uses it. Its calibrated 2 times a year, and uses a dial gauge built in it. Goes from 0 - 80Nm.

Just tourqed down the main cradle, but now my crank sort of "binds".

When the crank just has been turned around, it will spin free, and only require ~2 N to be turned. (You cant really measure it as it really doesnt move on the dial.) Easy to turn by hand.

When the crank hasnt been turned for a minutte or so it "binds". Will need around ~5 N to get it to spin free again. (On the dial gauge you can only see it move, and then drops back to nothing as the crank begins to turn / frees it self from the "bind")

Is this just oil friction I have to overcome just when turned? or?? Could this be a problem?

Best Regards

Ronni

Link to comment
https://www.sau.com.au/forums/topic/180559-is-this-okay/
Share on other sites
nissan200sx.dk Community Regular

nissan200sx.dk

Posted
  • Author
Posted

The applied force just need to be a little higher to get it to turn over when it has been standing still for a little minutte or so.

After it has begun to turn the applied force to turn it is close to nothing. It turn freely the hole way round. There are no spots were it feels more or less freely to turn.

Link to comment
https://www.sau.com.au/forums/topic/180559-is-this-okay/#findComment-3283101
Share on other sites
nissan200sx.dk Community Regular

nissan200sx.dk

Posted
  • Author
Posted

Have measured both crank and cradle, ordered correct bearings, got the ordered bearings. Mounted with clean surfaces (back side of bearing) and used plenty of motor oil to lubricate.

When it is turning it feels free and top nice. My only concern is what it is that is "holding" it when it hasnt rotated for a minutte or so. What i need to overcome for it to turn.. Could it just be oil friction? Because when using the tourque dial gauge the applied force to get it turning (when i have to overcome what is holding it) is only just the needle moving, only just moving, not even up on the dial...

But when it has just been turned, and then turned again there is nothing holding it. The needle doesnt move to turn it.

Tomorrow i will try with a different tourqe dial gauge. goes from 0 - 8N. Should be apple to see more accuratly.

Link to comment
https://www.sau.com.au/forums/topic/180559-is-this-okay/#findComment-3283150
Share on other sites
SilverECR33 Veteran

SilverECR33

Posted
Posted (edited)

On older engines, it was perfectly fine to use oil, i cannot comment on whether grease would have been better or worse. But I thought your not ment to use grease on ur main cap bearings.

What I can say, (which sounds like your describing), is that when the crank is stopped, its harder to get moving, then once its free its fine. then when u stop, it sort of sticks.

On the last rebuild on my v8. The crank did the same thing. and it was perfectly fine. If your really worried about it, borrow another torque wrench, and retorque it. and see if its the same.

since their is no oil pressure, the bearing oil hole and groove, can only pickup oil from spinning. when you sit still, the oil is pushed back off the bearing into the groove, you have to then spin it to pick up the oil into the hole and groove again.

Thing is, you must still be able to move it buy hand, at the correct torque. if its harder than that. its possibly too tight.

but i would rather a professional post here. as Im a novice. good luck.

Edited by silverbulletR33
Link to comment
https://www.sau.com.au/forums/topic/180559-is-this-okay/#findComment-3283710
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Marek
      Hi everyone.

      By Marek · Posted

      Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Marek
      WGNC34 - floor mats

      By Marek · Posted

      Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • ARB26
      S1 Autech 260RS Wiring Diagrams

      By ARB26 · Posted

      I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
    • MBS206
      Hi everyone.

      By MBS206 · Posted

      I believe @Duncan has given it a crack at Mt Buller before (in actual race conditions)
×
×
  • Create New...