Jump to content
SAU Community

Recommended Posts

Hi i recently purchased an apexi power fc for my series 1 r33 its brand new with hand controller i set it up as per the manual that came with it, when i start the car it starts and idles very roughly and it only running on 4 maybe 5 cylinders and is poring bulk fuel into it (all i can smell is fuel) from the exhst. I put the same ecu into my mates car a ser 2 and it runs perfect i can not work out whats going on anyone got any ideas?

Thanks lars

hey man, i had similar probs with mine n it was just the connections on the loom plug bolting to computer, wasnt 100% straight, the reason your smelling fuel is because its not being burnt by 1 or 2 of the cyls so is going into exhaust, try take plug off and retighten it and make sure its on straight to eliminate that...cheers and good luck

etc, version

what do you see?

etc, sensor sw / check

anything highlighted in black?

what do you see?

is the engine check light (orange) on when you have the problem?

have you performed the self idle learn procedure properly ?

I think it was version 5 for rb25det

nothing high lighted in sw check

engine light was on at first due to boost control on turned it off no light

the light is off when its running i did the idle self learn properly

car just runs on 4 cyl runs perfect on mates ser 2.

Thanks

etc, version

what do you see?

etc, sensor sw / check

anything highlighted in black?

what do you see?

is the engine check light (orange) on when you have the problem?

have you performed the self idle learn procedure properly ?

Check the plug again and make sure the bolt bottoms out. All bets are on the plug not being 100% true and in as with some cars the bolt can be very stiff to do up making you think its done all the way up but its not. Tripple check. :wave:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
    • Just like in being 14mm too small (296mm) makes it not fit, being 14mm too big (324mm) it also won't fit. You want to find the correct rotor.
    • @GTSBoy Ok so that was the shops problem...they showed R33 rotors on R34 page and i did not know 296 do not fit(and are for R33) Yes i bought "kit" with rotors and pads. Pads are ok(i have GTT calipers front and rear). They have some 324mm but no 310mm. So i dont know if they would fit. I have 17inch LMGT4s So another question. Can i fit those in the rear or they are just "too" big for that?
    • I started removing the tank a while back with the intent to give it a proper clean. Got to a bolt that I couldn't undo completely due to a diff being in the way, so just said f**k it and siphoned the gluggy old fuel out and called it a day. Looking it the tank it looks less corroded than the one in the pics for that billet hanger from Frenchy's anyway. Isn't it the fuel filters job to worry about this stuff? I scraped off most the crusty shit of the hanger but will give it another go before reinstall coz maybe the fuel and return pipes are also full of gunk  
    • Pretty sure it is a common fault. I believe this is the only part you need, but don't quote me as I don't have a V36.  I also believe it is a bit of a pain to change and the device needs to be encoded to the car once it is replaced, so may need someone with the right tools. Buy Genuine Nissan 48700JF00D (48700-JF00D) Lock Set-Steering. Prices, fast shipping, photos, weight - Amayama
×
×
  • Create New...