Jump to content
SAU Community

Dragme Cracked A 9

FineLine

By FineLine,
in Motorsport Discussion & Builds

 Share

Recommended Posts

9krpm Mentor

9krpm

Posted
Posted
'DRAGME' are the car's number plates, so I assume it's still street registered in Qld

That still doesn't mean that his street registered car is the one at the drag strip :) or he use all of this power on the street.

Common guys, don't you guys know that the police get on this forum too. You might as well go to a police station and report "DRAGM3" rather than talking about street registration on here :)

Congrat for the 9sec. I love to see the video.

Lithium Grand Master

Lithium

Posted
Posted
It's an R33 GTS25t with a T51R bolted to what sounds likr eitehr a 26(possibly stroked) or a 30?

Although i could be mistaken it could just be a modded 25?

Awesome :pwned: Thanks! Here's hoping its a RB25DET for a change.

skybarge Community Regular

skybarge

Posted
Posted (edited)

I'll drink to that, a 25 would be a nice change

Here's a vid off youtube:

I could only find three :pwned: i slowed it down when it flicked between things and it's definitely a T51R kai, not sure about the engine though

--Gazee just pm campbell and ask him yourselves lol--

Haha i might have to :thumbsup: he's done a top job

Edited by skybarge
ECR033 Mentor

ECR033

Posted
Posted
That still doesn't mean that his street registered car is the one at the drag strip :( or he use all of this power on the street.

Common guys, don't you guys know that the police get on this forum too. You might as well go to a police station and report "DRAGM3" rather than talking about street registration on here :thumbsup:

Thanks for the insight :P

If the car is street registered (which was only an assumption), i'm sure it's engineered, so I'm sure there's no problem...

funkymonkey Grand Master

funkymonkey

Posted
Posted

I met campbell when he was still building up the car... he was sayin something about some dodgy russians who had screwed him over with the buildup. in fact I think one of our cars has his old red leather interior in it still... from memory he was running a stroked 25. although that was a few years ago, he could have changed the engine now.

  • 1 year later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      What should I do next to hold the head on

      By Dose Pipe Sutututu · Posted

      Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Dose Pipe Sutututu
      boost source Size Garrett gt28 gen2

      By Dose Pipe Sutututu · Posted

      Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • oHBoy.
      2001 R34DE

      By oHBoy. · Posted

      3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...