Jump to content
SAU Community

Quick Question About Alarm + Install

Epyon

By Epyon,
in Car Audio & Electrical

 Share

Recommended Posts

Epyon Enthusiast

Epyon

Posted
Posted

I'm about to get an alarm and turbo timer installed (which my car has neither so far)

What i need to know is should i do them both at the same time?

Or should i do Alarm first followed by turbo timer?

Or turbo timer first so that the alarm can be installed to recognise the timer??

Basically is there any compatibility issues with the order of installation..

Alarm in question is the Mongoose M80G

And turbo timer is the Apexi black pen shape one....

Thanks in advance

Link to comment
https://www.sau.com.au/forums/topic/182694-quick-question-about-alarm-install/
Share on other sites
Chris Rogers Grand Master

Chris Rogers

Posted
Posted

wont make any difference. timer and alarm at once would be my pick if i was doing the car. that means I would only slice the harness once.

who's doing it? (pm me.)

GTRBOYZ Community Regular

GTRBOYZ

Posted
Posted (edited)

I ve been doing car security and Audio and electronics for over 10 years time to put my knowledge in use and help people.

1. Who doing your alarm?

2. DO your turbo timer 1st if u like or same time.

3. M80G have a turbo funtion which allow car to have ignition on while u can activate the alarm by pressing hold button I for 3sec.

4. Hook the up the ignition senser of the alarm after the the turbo timer but before immobiliser( if u decide to cut the Ignition)

5. Incase u dont know how to activate the turbo feature. Turn Turbo timer off 1st then make sure all doors, boot and bonnet are shut. Arm and disarm the alarm. Open the driver door then turn the key from ignition on to off 13 times u will see 13 flashes from blinkers and beeps. Then press button I once. You should hear a confirmation beep once. Close door or turn ignition back on to save and close programing mode.

DOne!! any problem PM me cheer

Edited by GTRBOYZ

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Rb26/30 build

      By MBS206 · Posted

      And if you want more power, more reliably, and cheaper, go get the Aussie RB... The 4L Barra and put that in instead.
    • MBS206
      Nismo rear spats

      By MBS206 · Posted

      No cats will keep discolouring the rear bar. Sends white paint a weird yellow stain. Cut and polish normally gets it out, but you'll be doing that every fortnight I found.
    • Butters
      Rb26/30 build

      By Butters · Posted

      Both heads will be equally reliable or unreliable depending on what you do to them.  Stock the RB26 head will flow more. You have access to the stock intake ITB manifold on the RB26 cheaply which flows really well(1000hp+).   Arguably more aftermarket support for RB26, though in Aus we love our RB30 SOHC heads too.    The only downsides to the RB26 head is if you have a VL commodore and want to keep the SOHC look.  Where you may have an issue is drilling out the rb30 block for the bigger head studs but if you are building a big power motor you'd probably put bigger studs on the SOHC head too.  This is just about finding a good machine shop, sometimes easier said than done.  RB30 head worked can make big power just like a Rb26 head, so really it actually more comes down to what your preference is for your car.  People now even making billet versions of both.
    • GTSBoy
      Rb26/30 build

      By GTSBoy · Posted

      2630s work perfectly well. There is something to be said for just using the 30 head, as it saves all the pain of the conversion, still makes tons of power, still sounds cool, etc etc. 2630 will obviously make more power again, but the differences are not stupidly big. It really depends on whether you're racing for sheep stations or not. If it's dead serious, then it's a 26 head. If it's just for fun, it could go either way. But the 26 head and the effort to get it set up, etc etc, is part of the fun.
    • lilley's gtr
      Rb26/30 build

      By lilley's gtr · Posted

      I've been building a 26/30 for a few years now. I've had the head built with all the good stuff. I had a 32 gtr but blew it up and yes its all going into a vl but im looking for some advice from some RB nuts on pros and cons on putting a 26 head on a 30 bottom end is it worth it Works are as follows Head -Extensive porting 1mm oversized supertech valves Supertech double springs Supertech valve guides Supertech titanium retainers Tomei solid lifters Tomei 270 x 10.25 cams Head drain Bottom end series 2 rb30 block Cp ceramic coated pistons Eagle rods Romac balancer Oil restrictions  O ringed blah blah spent a fortune And will get a girdle because the 30s arent used to handling that much rpm Nitto billet oil pump Hypertune plenum 6boost mani Refurbed astra pump thats the cover for it in the boot I did have a precision 6262 but sold it because drag car life. Currently building the ass end full 4 link floater rear end with a 2 speed  But the dilemma i have is my mate rekens I should just stick with the 30 head for reliability. Has any one had any issues with mounting the 26 head ie compression blowing gaskets etc. Just looking for some advice from people who have gone down this route. Here's some photos. Blew the oil pump in the gtr and decided to rip the motor out at the time and do a full build only to find it had been a repairable write off so went down this path.     
×
×
  • Create New...