Jump to content
SAU Community

Recommended Posts

Installing a manual boost controller on an R33 (stock intercooler)

Things you need:

Pliers

Rag

Small bolt

Cable ties

WD-40 (optional)

Cotton Buds (optional)

Time: 20-30 mins

Difficulty: Easy

For this guide I used a TurboTech (TT) boost controller. I've written it for the guys i've seen posting that aren't sure what manual boost controllers do, or how to install them. It's a small job and not worth getting a mechanic to install if you have the time. There's other threads about manual boost controllers, and also about the TurboTech valve, but i've tried to be more detailed. Feel free to give comments & suggestions.

Here's how to install it:

Locate the factory soleniod on the right side of the engine bay. Here's what it looks like:

gallery_41505_11_38452.jpg

First you remove the top hose form the solenoid. It's a bit hard to budge so if you can't do it by hand grab some pliers and wrap a cloth around the hose before you start twisting it off. Once it's loose plug it with a bolt and cable tie it.

Same story with the second hose on the solenoid. Remove it, it's connected to a tee-piece. The tee sits between hoses connecting the intercooler and wastegate actuator. The TT valve will replace the tee-valve here:

gallery_41505_11_7817.jpg

There isn't much room to budge the tee out, so instead of risking a cracked or broken hose from excessive jerking just remove the hose connected to the intercooler. I sprayed a little WD-40 to make it easier, and used cotton buds to clean inside after it was off.

Now you just remove the hose from the tee-piece, remove the tee and you'll have a missing space ready for the TT.

Before you install the TT valve between the hoses adjust the bleed screw so you can blow freely into the top left barb. This keeps the boost level safe for initial adjustment.

Install the valve so it looks like this:

gallery_41505_11_35022.jpg

Make sure the clamps are fixed firmly to the hoses to prevent air leaking, or hoses popping off under pressure. Cable ties can also be used.

So that's the finished product. The boost adjustment only needs 1/4 or 1/2 turns at a time. It's very sensitive so don't go crazy tightening it. Clockwise increases boost, anti-clockwise reduces it. It's safest to test it initially 'open'.

Make sure when you take it out for a test you have a boost gauge - the valve works without it but it's just safer to recognise boost spike.

Here's a quick list of BAR=PSI conversions so you can accurately read the boost levels. As far as i know stock Skyline turbos should be kept at about an 11psi/0.75BAR limit, as a short spike at higher boost could damage the turbine.

1 BAR = 14.5 psi

0.9 BAR = 13 psi

0.83 BAR = 12 psi

0.75 BAR = 11 psi

0.69 BAR = 10 psi

0.62 BAR = 9 psi

0.55 BAR = 8 psi

0.48 BAR = 7 psi

Enjoy the extra boost!

Notes:

You should test the boost in different gears. I found that 3rd boosts a couple of pounds higher than 2nd. So try different gears throughout the rev range.

Also you'll notice a serious mid-range power increase. That's where this valve does its best work.

A final note- the hoses you connect to the TT valve have small round 'lips' inside which can cause some air restriction. Consider replacing these hoses with hollow ones for improved airflow. I haven't tried it, but i'm assuming it might bring on boost faster. nissansilvia.com has a thread talking about replacing the factory boost hoses.

Good luck! :)

Edited by R338OY

u forgot to add band aids to ur parts needed list for when u pull on the hose that joins on to the t-piece and u take all the skin off the top of ur knuckes when ur hand fies off and bashes in to the top of that radiator support. yeah it did hurt!

i havent installed a t-piece in my beast coz been using a r32 actuator,

but i was always under the impression that all that was necessary was to connect the t-piece where the factory solenoid is?

isnt it the same sorta deal? the t-piece replacing the factory solenoid in controlling the pressure?

u forgot to add band aids to ur parts needed list for when u pull on the hose that joins on to the t-piece and u take all the skin off the top of ur knuckes when ur hand fies off and bashes in to the top of that radiator support. yeah it did hurt!

Yeh, take a look at my hand in the third photo... :)

i havent installed a t-piece in my beast coz been using a r32 actuator,

but i was always under the impression that all that was necessary was to connect the t-piece where the factory solenoid is?

isnt it the same sorta deal? the t-piece replacing the factory solenoid in controlling the pressure?

Yeh spot on, the boost controller does exactly that. The spring and ball bearing inside blocks/leaks air to the wastegate actuator at a psi level you want to set, rather than the factory system (on R33's) keeping it between 5-7psi only.

I'm running about 11psi but i was told the factory turbo can take up to 14psi ( :) ), but no more.

Oh yeh i found that inside the tube from intercooler to boost controller is a small brass/copper restrictor that can be pushed out with a screwdriver. I took mine out and boost comes on stronger, earlier, though i didn't notice a massive difference.

Anyone done the same?

  • 1 month later...

i have the same boost controller which im planning on using on R32 GTR.. do i just remove the two lines going to the stock solenoid and plug it into the manual boost controller?? which line carries pressure for intercooler?? any thoughts??

  • 4 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
    • So, a bit of a side trip, but one that might be interesting for people with JDM cars and japanese head units. I know @Pac previously posted about a carplay/android auto adapter he installed which used the AUX input, and @V35_Paul put in one of the Tesla style units that replace both screens. The option I went with was a Lsait LLT-YF-VER5.87_2 (https://www.alibaba.com/product-detail/Lsailt-8GB-Android-Multimedia-Interface-for_1601187633672.html). Price was $1,150 for a single unit although they are much cheaper if you are willing to buy 2....$857ea. Make you you get the version 2 not version 1, it is faster and has a better UI - this is the manufacturer listing: http://www.lsailt.com/product/348.html. BTW if you've never bought from Alibaba before, don't be concerned....these guys can't stay in business unless they are responsive, ship fast etc, they were excellent (probably faster shipping than most local places) So, this was my task for a lazy Sat afternoon....looks complex but was all done in a few hours (it probably helps that I had some of it apart before so it was a bit familiar). I also decided to add a HD USB drive recorded at the same time and the unit also supports an aftermarket reverse cam (if you don't want to retain factory) and also AV in and HDMI out It looks much worse than it is, in fact in was genuinely all plug and play (no custom wiring at all). This video was pretty good (skipped a few steps), unfortunately they are an Aussie seller but no longer sell this unit (I guess Carplay/AA adapters are easier to install and much cheaper) https://www.youtube.com/watch?v=T5hJfYOB8Dg
×
×
  • Create New...