Jump to content
SAU Community

Recommended Posts

Has anyone else had problems with their front tyres scalloping(wearing unevenly, numerous flatspots on inside)? I took my car in to have it checked out at Pedders, as i thought the noise was a wheelbearing, and they told me it was actually that my fronts were scalloping badly on the inside, which normally means a collapsed shock or two, but strangely mine were fine. He then put it down to cheap tyres, and that my wheels he'd never seen on a skyline before so they may not have been suitable for it (but i think he'd never seen NA wheels before).

Long story short, one set of new wheels and tyres later, and it's starting to happen again. Anyone had this before? or should i just head back there, with the suspension report and suggest maybe they got it wrong, and ask what they'll do to fix it?

Link to comment
https://www.sau.com.au/forums/topic/183516-scalloping-fronts/
Share on other sites

well, they're the ones that were on the car when it came across. so presumably the original shocks. It'd only done 56k at the time, and they've never given me trouble so i never considered a problem.

Is there an easy way to check the camber (i know comparatively little when it comes to susp.)?

Is there an easy way to check the camber (i know comparatively little when it comes to susp.)?

it would have been the perfect opportunity while your car was at pedders to get them to read your camber settings. I am surprised that they didnt unless it is on your report? its pretty difficult to tell what camber you are running with the naked eye especially if its only 1 or 2 degrees. if you are running too much negative camber (which is good for handling but bad for tyre wear) your tyres will wear on the inside.

but that doesnt explain the scalloping effect. I would get a second opinion from someone like Fulcrum Suspension.

well camber is not adjustable on a 33 GTS so forget about that. neither is caster. they are both worth checking purely to make sure nothing is bent, but they cannot be adjusted. I would say most likely this is being caused by incorrect toe or possibly a bent suspension arm. how does the car feel to drive?

same as it always did really, i've never noticed anything different, slight pull to the left when you're not holding the whell maybe. I did have a low speed impact a while back (rearended a motorcyclist at an intersection) - maybe that did something.

Are these Fulcrum guys good? i've never heard of them before.

i got the same problem. i had to take my shocks out when going over the pits and found my shocks are rooted. can be compressed by hand. this was about 2 months after pedders said they were in perfect working order. go somewhere good. a lot of bogans work at pedders.

same as it always did really, i've never noticed anything different, slight pull to the left when you're not holding the whell maybe. I did have a low speed impact a while back (rearended a motorcyclist at an intersection) - maybe that did something.

Are these Fulcrum guys good? i've never heard of them before.

you've probably never heard of Murray Coote before though either :D

As previousley mentioned worn shocks will wear the tyres like this, another cause could be hard braking as the wheel alignment changes under hard braking. You can eliminate the wear by rotating the tyres at regular intervals (if you have the same size wheels & tyres front & rear or have the tyres turned on the rims to swap side to side if you have directional tyres)

Carlos

im an aligner by trade and i just fixed this on mine it was worn out caster rod bushes and i completely f*(ked the inside edges.neway i would get a alignment done asap when was the last time u had one done they should be done at least once a year or at least when you get new tyres

another cause could be hard braking as the wheel alignment changes under hard braking.

I doubt it would be that, my car's never seen a track or similar, the closest it gets to hard braking is jaunts along the Ocean Rd and surrounds :nyaanyaa:

i just fixed this on mine it was worn out caster rod bushes and i completely f*(ked the inside edges

Yeah, i'm planning on an alignment asap. What did the caster rod bush replacement cost?

I doubt it would be that, my car's never seen a track or similar, the closest it gets to hard braking is jaunts along the Ocean Rd and surrounds :)

Yeah, i'm planning on an alignment asap. What did the caster rod bush replacement cost?

well i did the work myself at work n got trade and it was about 100 bucks but i know the guys at pedders so i got really well looked after i think retail is 190ish but i wouldnt qoute me.good luck

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That's not a transistor --- it's marked ZD1 which makes it a zener diode. As to what the breakdown voltage is, not enough there to divine.
    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
×
×
  • Create New...