Jump to content
SAU Community

Skidpan Day At Sutton Driver Training Centre 11th November


Recommended Posts

payments closed

As a November event, We want to try and hold a skidpan day at Sutton Driver Training centre, on the 11th, 8am till 12:30pm. The skidpan is wetted down with sprinklers, so tyre wear is reduced. For more information about what to expect check out www.fifthgear.com.au . For this event to proceed we will need at least 10 participants ideally. If more people express an interest the day may be expanded to the afternoon. And the cost may be reduced. Maybe get a BBQ happening as well.

Have been to quite a few of these myself, they are great fun, but be warned your car gets quite dirty from the water on the skidpan.

So to Summarise:

Date: 8am - 12:30pm 11th of November

Price: 99$

What you get

* Introduction to drifting and skid control

* One-on-one coaching

* Free time on skidpan

* Drinks provided

Location

* Sutton Road Driver Training Facility

* RMB 300 Sutton Road (off Pialligo Rd), Canberra

What you need to provide

* Own vehicle

* Suitable clothing and appropriate footwear

* Payment and booking form prior to session

Participants:

1. CeJay (Paid)

2. R33Drifter's gf (Paid)

3. LadyBytes (Paid)

4. Turismo (paying dereck seperately)

5. R33Drifter (Paid)

6. R31 Forum member (Paid)

7.zenith13(Paid)

8.rb20tr32(Paid)

9.Bnr32t (Paid)

10.

11.

12.

13.

14.

15.

I will include payment details shortly if enough interest is expressed in the event. Payment of a deposit would be due by 14th of October.

  • Replies 82
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Will probably at this stage open payments on the first of october and close it around the 11th, to ensure numbers. Will be having one session at this stage, if numbers allow, may extend the session to six hours.

Also by the way who would be interested in doing some timed course stuff on the skidpan like what we did in Texikhana? I had a ball doing that stuff as well. Just an idea

The small wet skidpan at sutton is what will be used. Just a quick note, the format normally consists of 3 or 4 runs on the skidpan of 15 minutes each, 2 cars on the skidpan at a time.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...