Jump to content
SAU Community

Skidpan Day At Sutton Driver Training Centre 11th November


Recommended Posts

payments closed

As a November event, We want to try and hold a skidpan day at Sutton Driver Training centre, on the 11th, 8am till 12:30pm. The skidpan is wetted down with sprinklers, so tyre wear is reduced. For more information about what to expect check out www.fifthgear.com.au . For this event to proceed we will need at least 10 participants ideally. If more people express an interest the day may be expanded to the afternoon. And the cost may be reduced. Maybe get a BBQ happening as well.

Have been to quite a few of these myself, they are great fun, but be warned your car gets quite dirty from the water on the skidpan.

So to Summarise:

Date: 8am - 12:30pm 11th of November

Price: 99$

What you get

* Introduction to drifting and skid control

* One-on-one coaching

* Free time on skidpan

* Drinks provided

Location

* Sutton Road Driver Training Facility

* RMB 300 Sutton Road (off Pialligo Rd), Canberra

What you need to provide

* Own vehicle

* Suitable clothing and appropriate footwear

* Payment and booking form prior to session

Participants:

1. CeJay (Paid)

2. R33Drifter's gf (Paid)

3. LadyBytes (Paid)

4. Turismo (paying dereck seperately)

5. R33Drifter (Paid)

6. R31 Forum member (Paid)

7.zenith13(Paid)

8.rb20tr32(Paid)

9.Bnr32t (Paid)

10.

11.

12.

13.

14.

15.

I will include payment details shortly if enough interest is expressed in the event. Payment of a deposit would be due by 14th of October.

  • Replies 82
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Will probably at this stage open payments on the first of october and close it around the 11th, to ensure numbers. Will be having one session at this stage, if numbers allow, may extend the session to six hours.

Also by the way who would be interested in doing some timed course stuff on the skidpan like what we did in Texikhana? I had a ball doing that stuff as well. Just an idea

The small wet skidpan at sutton is what will be used. Just a quick note, the format normally consists of 3 or 4 runs on the skidpan of 15 minutes each, 2 cars on the skidpan at a time.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
    • Not sure yet.  Was considering speedtek because it was rated to 800hp, but when I did some research about him I don't think I will go for that🤣 So maybe giken gear set, but I'm afraid it won't be strong enough🙄
    • Keeping in mind that for most people this is a week to month long job!
    • Its also worth mentioning that 30 years after it left the factory and god knows how many missed oil changes since, there is every possibility that one or more lifters are ticking because they are sticky/gummed up. To resolve that you need to pull the cams then pull each lifter, disassemble, clean, reassemble, soak in oil and re-install, and they should come up good as new.
×
×
  • Create New...