Jump to content
SAU Community

Recommended Posts

Hey guys!

Was wondering what the lengths of a coupe and sedan are and

if there is any difference?

The reason being, is because i was wondering if you could get coupe

side skirts and fit them onto sedans ? :spank:

Thanks

Samir :(

This information is for the 33's coupe and sedan.

For the coupe's:

Exterior Length 4640mm

Exterior Width 1720mm

Exterior Height 1355mm

Interior Length 1820mm

Interior Width 1415mm

Interior Height 1090mm

Wheelbase 2720mm

Front Track 1460mm

Rear Track 1470mm

For the sedan's:

Exterior Length 4720mm

Exterior Width 1720mm

Exterior Height 1375mm

Interior Length 1895mm

Interior Width 1425mm

Interior Height 1115mm

Wheelbase 2720mm

Front Track 1460mm

Rear Track 1470mm

Hope that helps.

Edited by adam-__-

You'd have to get a plastic welder to extend them or something. Also 2-door's have this bit on the side skirts that rise above the door level and 4-door's obviously have a door there so that would have to be modified too. Just look at some pics if you don't understand what I mean.

Thanks for the info Adam >_<

So do you think i'd be able too fit

normal side skirts onto my sedan?

You'll be able to get coupe skirts to fit your sedan, but it will involve a lot of modifications to the skirt. Best to buy a kit made for the sedan mate. :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...