Jump to content
SAU Community

Recommended Posts

stupid question, but have you checked that it's not the dust shields behind the discs rubbing on the discs themselves?? It's very easy to bend them accidentally when installing new discs, and it can sound similar to what you've described... I'd be having someone in the car, letting it roll slowly (engine off, and brakes disengaged) while you listen at each corner. Just my 2 cents: I've been caught like this before.....

  • Replies 51
  • Created
  • Last Reply

Top Posters In This Topic

  • 3 months later...

Hi All

I know nothing about brakes, besides the fact that they stop my car. Currently have a GT-8 sedan and don't think that the brakes are strong enough.

Thinking about upgrade. Any brake guru's out there know if I can put R33 GTS-T brakes (full set front and rear) onto my car? And would they make much of a difference? Would love the brembos but way too expensive.

Thanks in advance.

You'll need to check that the distance between the R33 caliper bolts are the same with V35's, but if you're not doing the install yourself then a brake shop can always fabricate something for you to mount the r33 calipers.

Attached is a size reference chart, the R33 gts-t hat height is higher than the V35 so depending whether you're gonna be keeping your V35 rotor on the front, you also need to check the clearance between the caliper and the rims, especially if you have the std 17" rims. the optional V35 18" or 19" rims should be fine with these.

post-328-1222209937_thumb.jpg

Also I've finally put the brembos and grooved dimpled on the V35 with some redstuff, they're done by RaceBrakes, hardly any noise on medium/hard brake application but still squeals a bit on light application. But again, I had them 2 weeks ago, and so far I've only driven the car once a week and less than 100km since fitted. But the bite is absolutely a class different compare to the stock V35 calipers.

I still believe upgrading to brembo is the best way - there's a few cheap 350z brembo caliper set going on ebay at the moment, mostly in USA (check the sellers if they're willing to ship it down here), but again, R33 gtst calipers are definitely cheaper, and even if they're not brembos, they are considered very good calipers already compared to what's fitted to most other cars from that era.

Just to quickly add - make sure you check the R33 calipers you're purchasing are not leaking, and they come complete with the pins and metal clips that hold the pads, as well as the steel brake pipes section coming out of the calipers. If they're only missing the rubber hose section - these are easy to replace, but having those steel section & small parts for the pads will make your life easier when swapping.

I Think if you need to upgrade you brakes for street use, just change to EBC Green stuff or Nismo pads will do. That's the cheapest upgrade and you get 20% more biting power from after markets pads. Correct me if I'm wrong.

  • 2 months later...

Hi there, has anyone changed the front rotors themselves? I had a go at changing them this morning, I removed the wheel and the caliper. I expected the rotor to simply pull off but it didn't. A few taps around the hub with a hammer did nothing to loosen it. I could not see a fitting screw or anything - should the rotor simply pull off - I am guessing that it is simply siezed to the hub a bit.

Thanks, Ben.

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, I started this repair and got as far as "fixing" the holes with some fibreglass. God all those years working on boats came back quickly. I decided I'd reach out to some rust guys just to see what they would say about it. I came across a guy about 40 mins away and went to see him. He said the windscreen needs to come out, that there might be some more bits around the windscreen and he'd quote them at the time. But his quote was $300 to remove and replace windscreen and $3k for the damage he can see. He said he could respray the roof for $1200 and the bonnet for another $800 (somebody has previously rattle canned it, its horrendous). This is $5300 + any small additional bits. It's a lot, I get that and the name of one of my fave youtube channels 'Not Economically Viable' comes to mind.  I'm not being financially rational, but I've taken him up on the quote. He's opening a new shop in November with more room, so we're waiting for that. I'll leave the currently missing headliner out until then. I'm looking forward to it being fixed and having the paint looking nice again (lots of clear coat issues on the roof too). / flame suit on.
    • Oh and some up-and-comings; New rear drivers wheel bearing. I'll do that this weekend while the diff is out. The car is already up and the d/c axles and missing exhaust will help with space. This is the last bearing for me to do and I've been dragging my feet on it. I also have some new EBC blue stuff pads for the car and some new brake fluid. I haven't ever flushed the fluid in this car and looking forward to it. I have 600 degree fluid to put in. Not exactly "race fluid" but better than the typical stuff I have been using.
    • A proper clutch/plate type mechanical diff with quite a lot of pre-load and high locking % is better for drifting. Much more consistent in its behaviour. A helical can be annoyingly vague and inconsistent in how it responds under the sorts of abuse found in drifting.
    • Some updates here. I pulled the entire interior out, minus some trim to respray the seats with Colourlock dye. It turned out really nice though I accidentally let the dog in the car after and she scratched up the front seat.  This is what it looked like before, the colour was just washing out everywhere but thankfully the leather was in good nic. Then after the respray   And after the bloody dog jumped in The headliner is out waiting to be retrimmed, but it will stay out now until Nov - see why below. I replaced the stereo/headunit with a period-styled Android headunit. I have no after pics, but I'll get some. This is because of the missing pixels. I tried to fix this twice with replacement ribbon cables but couldn't. Also the bluetooth interface I'd bought for this was crap. Then there's the rusty roof. Pics and info in this other thread. I have decided to get this repaired professionally, but I'll update that thread. This is why the headliner will stay out for now. I'll be getting the roof and bonnet resprayed at the same time the rust is fixed. I also had an interesting issue with my drivers door lock.  For a small period I was having issues getting any 12v power to the car - I mean *any*. It would have no dash lights, nothing. It happened while I was at the shops and I couldn't get in the car. So, we had 2 problems. The most pressing here is that I was locked out. I have only a single physical key hole on the car, the drivers door and no amount of turning would unlock the car. Surely it doesn't need power for this? The second issue is why am I losing all power periodically, The battery isn't dead, its almost like the battery isn't even there. Two issues that were surprisingly easy to fix. You fellow BMW over-engineering lovers will appreciate this. The lock in the door has 5 states; mechanical lock, electric lock, neutral, electric unlock, mechanical unlock achieved at -90 degrees, -45 degrees, 0 degrees, 45 degrees and 90 degrees. Although, the unlock is towards the front of the car, so opposite for LHD countries. Sticking the key in and turning 45 left or right is what is used 99% of the time. It activates the central locking etc. 90 degrees is for dead battery access and, obvs, only un/locks the one door. But because the mechanical lock is never used and is 27 years old, it seizes up. I was totally unable to turn the key far enough to get to the mechanical unlock (At the time of locking myself out, I didn't even know this was a thing). I eventually did it with some vicegrips and teflon spray.  I made a quick vid for other E39 peeps.   The battery issue is totally new to me also - It wasn't making sufficient contact between the post and the terminal. The terminal was bolted on tight, but the car wouldn't have power. After checking the battery with my multimeter I accidentally contacted the terminal and the battery post and the car got power. The battery was only a few years old and in good condition. I cleaned the post and the terminal with a wire brush, bolted it back on tight and never had the issue again. I'm still surprised that despite having solid contact it didn't work. Also, the car was getting Warragamba sized pools of water in the back when it rained. My initial concern was another rust problem. But when I went out on Weds while it was raining and while I had no headliner in I could see a steady stream of water coming through the roof mounted aerial. As this aerial is for the (now removed) car phone I pulled it out and whacked a blanking grommet in the hole. It seems fine now. I'm thinking I might get the hole permanently filled when the rust is fixed. Moving forward and things in progress; The tailgate needs some attention. I have taken all the trim off to clean it all and address some small rust spots. I have partially done all of this but I'll finish it up hopefully this weekend. As all the trim are now entirely devoid of trim clips I have bought a heap of strong velcro and I'm hoping it does a good enough job as any of this trim in good condition is super expensive and usually in Europe as we dont have many of the wagons here. Suspension and brakes!!! This is exciting. In the front; New control arms New sway bar links New lower Eibach springs (the only modification I'm planning on this car) M Sport shocks (these came with the car and will replace the longer shocks in the car) New top mounts Used 540i calipers (stock brakes suck!) New 540i disks and pads (22x296 mm for 528 and 30x334 mm for 540i) New front wheel bearings (thank all that is holy for bolt on bearings!) Annnnd in the back; New control arms New sway bar links Adjustable air suspension arms (fool the car into what the current height is so the self levelling suspension can match the new front ride height) New ball joints I'll also be doing a brake fluid flush while I'm in there. I'm planning on switching the car over to the 16's that came with it so I can clean up and respray the M Sport 17's. They've lost a lot of colour over the years and have some gutter rash. None of this will start until the E90 is back.
    • You mean you will regret it for drifting duties? I don't quite follow.
×
×
  • Create New...