Jump to content
SAU Community

Recommended Posts

  • Replies 92
  • Created
  • Last Reply

Top Posters In This Topic

I have Nexen N6000 on mine. Brand new came with the car when I bought it from the dealer. They are not bad for what they cost. Slightly more road noise at high speed and rough surfaces compared to expensive stuff like the Bridgestones. Grip is good and they are comfortable. Can't say much about the wear as I have got them for 2 months.

Just a heads-up on purchasing all, I just got my rear set of Hankook K110s from www.tirerack.com and they cost me $311 shipped for 285/30/19. The cheapest quote I got for the same tyre was $430 locally. Shipping cost for four tyres to Melbourne (25km-metro) was around $250 USD.

Also it seems the Bridgestone RE001 Adrenaline in America is called the Bridgestone RE760 Sport and they're really cheap compared to local prices. If you can afford to spend a wee bit more, the Yoko AD08s are awesome value.

The only catch is some credit cards that are not on the "Verified by VISA" program will not be approved and you'll have to make a USD wire transfer, which can usually be done for a small fee by your bank.

Delivery was done by fed-ex and they arrived within a week of payment. I will definitely be buying all my tyres from these guys from now on (except my Advan A050s seeing they don't have them).

Also it seems the Bridgestone RE001 Adrenaline in America is called the Bridgestone RE760 Sport and they're really cheap compared to local prices.

That's because the RE760s aren't the same as RE001s. The tread pattern is the same, but the tyre compound isn't.

The RE760s have a treadwear of 340, whereas the RE001s treadwear at 220.

Hi Guys,

i bout some new ku31's for $200 each from Option1 garage (225/40 R19 and 245/40 R19)

7 Remora St Hamilton QLD 4009 Phone: +61 7 3268 1113 Fax: +61 7 3268 2028

then just email/call and discuss price, i got them delivered to the comliance shop and even they couldnt get them at that price so they were a little shocked. I bought them about 2 months ago and cant complain, even in today wet weather the car hasn't slipped out on me as yet but a little bit noisy but its not annoying, any tyre will produce noise.

Hope this helps.

Cheers

ahhh time to buy tyres again.

Just bought 295/30/19 Pirelli P-Zero. $900 each :P lucky its only for the rear so i only needed 2, the fronts got a bit more left on em but i need to replace soon.

The negative 2.5 degrees camber has been eating away at my tyres, the price u pay for the look :P

Shit thing is i cant swap / rotate the 295's, but the 265/30/19 on the front i can swap them from each rim.

Edited by BLISTC

Yeah, the v35 sucks with the largish camber. Can't really square them up without getting aftermarkets. I'm running -2 on the rears.

For some reason, one side could go to -0.5 and the other side couldnt get under -2 :S

Previous owner(s) must've hit the kerb pretty hard or something?

My car comes with i think the stock Bridgestone Potenza. Anyone know how good they are compared to those tyres mentioned here? Thanks!

Think there are quite a few potenzas? What model. Think it reads RE002 or something?

All I know is that the Potenza is a fairly expensive tyre!

  • 1 month later...

Running on faulken f452's ATM, not bad but it is uneven tyre wear that will make any tire make noise. I am running on 350Z nismo suspension at the moment and the camber is doing a good job of eating the inside of the tyres.

The rims I got originally came with Bridgestone S02's & T02's, the T's are a run flat, which was disappointing when I had a blow out, hence the change, but the bridgestones were better grip wise.

I have had moments with the current tyres in the wet when you can feel that the ABS is going to start, and yet on the old Bridestones you could almost put your foot to the firewall and you just stop, without that felling that the ABS is about to jump in.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
    • OK, now we are ready to get started. You need to remove the air boxes on each side for clearance. The cover is straightforward, undo the clips on the top and lift the front cover out of the rest of the housing. If it is tight you can remove the air filters first. The rear section of the airbox is trickier. On each side you need to remove the Air flow meter wiring which is held to the airbox with a clip; you need to get behind the clip on 2 sides if you want to remove it without breaking it - unclip the harder side and pull on the clip with medium force, then unclip the easier side and it should pop out The airbox is held onto the intake hose with a spring clamp; you need to get a flat bladed screwdriver behind the spring on both sides and pop them outwards. When you have got them in the right unclipped place they will stay there and the airbox slips out pretty freely. Put a rag in the intake to prevent anything getting dropped in there, and also to prevent you seeing that the turbo seal is leaking oil (as they do). Then. The top of the radiator is held by a steel plate, it is secured by 2x10mm and 2x12mm headed bolts . Remove them and remove the plate Also grab the bushings that hold the radiator to the plate on each side so they are not lost!
    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
×
×
  • Create New...