Jump to content
SAU Community

New Bonnet/fender Badges + Front Bar Id

chestnut

By chestnut,
in Exterior & Interior Styling

 Share

Recommended Posts

chestnut Enthusiast

chestnut

Posted
Posted (edited)

Hey guys,

I was wondering where I could get new metal badges from. The one on the bonnet's looking a bit tainted from oxidisation (lots of little speckles etc)...and I believe the 'GT' badges on the front guards are meant to be white/red? At the moment mine are just metal in colour - not sure whether they were faded from the sun or what.

I noticed there seems to be 2 stock front bars for R32 gts-t's and gts-4's...ones slightly bigger with a bottom lip (as attached)...where can I get one of these?

Last question, if I were to get a GTR front bar, would it be considerably lower than the rest of the car if I left the stock side-skirts on etc?

post-42234-1190164965_thumb.jpg

Edited by chestnut
adam-__- Grand Master

adam-__-

Posted
Posted

You should be able to get the badges from a wrecker, but it could cost quite a lot. The badges on my gaurds are all silver. I think on the 33's, the ones with blue had turbo and red non turbo or something like that. I don't think that applies to 32's.

The GTR bar would/should be lower than the rest of the car if everything else is standard.

adam-__- Grand Master

adam-__-

Posted
Posted
Adam - my 32 is a gts-4 also...are they meant to be silver?

I'm not sure what they're supposed to be, but mine are silver. I don't think they faded either. Some people have there badges in GOLD!!

chestnut Enthusiast

chestnut

Posted
  • Author
Posted

Where's this r32 thread? I've been looking but can't find it.

Ok, aside from the badges etc...would I need to go to a wrecker to get one of these front bars with the bottom lip? ^pic in first post.^

chestnut Enthusiast

chestnut

Posted
  • Author
Posted

Okay cool...I'm happy then, mine hasn't faded or anything as silver badges seem to exist haha.

So the front bar I want is an M-Spec/M-type front bar? I guess I'll have to get one from a wreckers then.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • sonicii
      Could it really happen......

      By sonicii · Posted

      I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • MBS206
      Could it really happen......

      By MBS206 · Posted

      Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • MBS206
      R34 25GT Engine Light 21

      By MBS206 · Posted

      Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...