Jump to content
SAU Community

Can we hold a meeting with the police regarding the mods that are allow?


Recommended Posts

It would probably be much more accurate to get the rules and adr's in writing, otherwise the poor cops are going to have to know all the rules and regs off the top of their heads. I recently spoke to the engineers who did my brakes, and even they couldnt give me a definite answer as to wether a planned mod will be legal as they need to see it and how its been done to be able to tell me that.

If we can get hold of all the rules in writing and make them available to everyone, that would be a pretty good idea, might have to make some calls to qld transport.

Specifically for Queensland: Queensland Transport publish a booklet called Modifications. It can be picked up for free at any Queensland Transport customer service centre. It covers the basics if used with intelligence, however doesn't mention pod filters. They also have a website

www.transport.qld.gov.au/driving

Being English, and living in England until I was 24 I was brought up to see Police as people I could turn to for help if needed,and, as I have never had any bad experiences with police in my 39 years in Aust I tried to bring my boys up with the same belief.

I've had my Skyline since Oct 2001 and have never been stopped by police.

My son Mick has had his for 8 months and being stopped for no particular reason is a regularly occurring fact of life and he now sees police officers as being rude,overbearing, bullying, threatening and ignorant persons who should be avoided at all cost.

My point is I believe that young people driving Skylines and similar, modded or not are a targeted group and subjected to very different police behavior and attitudes than the average driver, I would not advise anyone in this group to take their Skyline anywhere near the police for any reason unless their life depended on it

Guest hoon69

agreed fully with you there 51jay,its not advisable to take any modded car or any nice car near police,as its most likely to get targeted as a hoon or racer etc..

its a shame what it has come down to...everyone being put on the same level as,most idiots who are reckless etc and are the real hoons..

So what about we get a full copy of the ADR's and before we hold a discussion with the cops (who will be all friendly & sweet-mouthed and encourage us to aspire to them), how about we have a cruise day where we stop by some engineer (who we all chip in and pay) and maybe they can give us general info (like boxed pods are ok compared to open pods or whatever) - then they can spend 5-10mins looking at each car just to see if we should get one or we are fine .

Wouldn't cost much money or time for us all and most (hopefully) of us will find out we are in the ok (and will have ADR sections to prove it), and those who are recommended to get one could all book (and maybe get group club discount).

my 2 c worth at least

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • UPDATE: Yes the GSP Axles are compatible. I installed it on my R34 today and they are working a treat! Turns out that the S13, S14, S15, and 200 SX all used the same axles as the HR34, and ER34 NA models. Which is 2 bolt x 3 pairs.  
    • Also build this EH ute with 370z motor and gearbox with a couple of turbos just for fun.  
    • Got the passenger door on plus the master cylinder and booster. Loaded up to take it home. At home, the colour changes a lot in the light.
    • Nothing cheap, but I have seen the AC Hydraulic DK13HLQ which is pretty close to what you're asking for. The problem is the hydraulic cylinder mandates that the back of the jack be a certain height and Skylines have fairly deep inset floor jack points. A more certain and cheap option is to get some nominal 2x10 inch lumber boards and have one board be 1.5 feet, the other board 3 feet. Glue it all together with lots of clamps to maintain pressure. Make two of these. The ramp suggested above is a good idea, it takes quite a bit of clutch slip to get over each of the boards. I only need the first ~1.5 inches for my low profile jack on a standard ride height car but a lowered car you want to go up to the full ~3-3.5 inches. Paint it or store indoors if you want it to last.
    • Ok. And Nistune? I read (here too) mainly on Stagea threads that it can by "turn off" with Nistune. But they say they still had the sensor plug in. Next week iam going to the Nistune(and other ECUs) tuner so i can finally make it work. I drove the car home and apart from the cut it drove great. No misfire no smoke no hesitation or rough start...so hoping it is this sensor that is missing  
×
×
  • Create New...