Jump to content
SAU Community

Recommended Posts

Hello my car is a R33 series 1

T2871r

Frontmount

full exhaust

Safc I

Profec B EBC (turned off untill tune) boost spikes to about 12psi

Stock ecu, injectors and afm

i recently replaced the coils which fixed my missfire. The other day i was driving it and under full load on boost felt like it started to do it again. Except this time it would fully stop for a split second then go again, then stop, and go again. Happens at higher revs and when my foot is to the boards. Car is untuned getting a 040 soon then will get it tuned. i have heard of fuel cuts on these maybe thats it??

Any ideas

cheers

Link to comment
https://www.sau.com.au/forums/topic/187342-fuel-cutboost-cut/
Share on other sites

Hello my car is a R33 series 1

T2871r

Frontmount

full exhaust

Safc I

Profec B EBC (turned off untill tune) boost spikes to about 12psi

Stock ecu, injectors and afm

i recently replaced the coils which fixed my missfire. The other day i was driving it and under full load on boost felt like it started to do it again. Except this time it would fully stop for a split second then go again, then stop, and go again. Happens at higher revs and when my foot is to the boards. Car is untuned getting a 040 soon then will get it tuned. i have heard of fuel cuts on these maybe thats it??

Any ideas

cheers

obvious problems highlighted above.

Try:

http://www.skylinesaustralia.com/forums/search.html&f=8

Edited by The Mafia

Firstly that link didnt work, and im not running big boost, nor is the turbo that much bigger than my stock one. I undersatnd that its those things however i know people making heaps more power than mine on the same stock set up. I need to know wat is actually causing this to happen. I dont just want to throw parts at it.

there is no boost cut

Its a flow cut, the more air, the more damage can be caused, so the ECU protects the engine.

You have a factory ECU and AFM which are guaranteed to be the problem.

If that link didn;t work, then at the top right hand corner, there is a button called "search", I suggest you use it because this problem is covered about once a day.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...