Jump to content
SAU Community

Recommended Posts

Needs more depth of field, lower shot angles and more sky behind the car rather than ground infront of the car.

other than that they're pretty good :laugh: also, late afternoon (about 20mins before sunset) is great for taking pics of cars.

Edited by B. J.

^They're right Cara - Need to get down on your knees when taking photo's of cars :P

Also for DOF - if you have the control on your camera, get away from the car, add zoom to fill the frame, and make the apature as large as possible (smallest number) ie. apature ~5.x

^They're right Cara - Need to get down on your knees when taking photo's of cars :)

Also for DOF - if you have the control on your camera, get away from the car, add zoom to fill the frame, and make the apature as large as possible (smallest number) ie. apature ~5.x

wouldnt know how to do that! LOL

cheers everyone for the input and advice, here are a couple others, i took on the angle, makes the car look a little weird tho, and the last pic i was lying on the ground(taken on a different day tho)

wouldnt know how to do that! LOL

cheers everyone for the input and advice, here are a couple others, i took on the angle, makes the car look a little weird tho, and the last pic i was lying on the ground(taken on a different day tho)

Hey Cara, the latter ones are good too.

For apature control, its the "A" on your control dial of your camera (finepix S6500fd as you said in your other thread) as seen below:

app_top_01.jpg

Read up on the manual about apature control with your camera and to get the Depth of Field you want, adjust the apature.

If you want ONLY the car to be focussed (ie. less DOF) then use long zoom and big apature, to focus on the surroundings too (more DOF) then use a shorter zoom and smaller apature. Remember though, whatever zoom you are at, try to fill as much of the frame with the car as you can as the car is to be the focus point of the photo.

cheers for that lee,

the next time i will be using the camera will be at gazzanats thid weekend, so i will certaintly play around this it and see what i get and post some up.

thanks once again!

Something else to think about

Boat ramp locations are very 1991 and you're shooting a car built in 1999, try and find a location that complements the age of the car - for example try and find a modern industrial complex or something that's only recently been built. Even underground car parks late at night are a winner provided the place doesn't look like it was built back in the stone age. Take your tripod if you're going to be shooting underground, the light levels won't be enough to shoot free hand. :)

Examples of modern locations that i've shot cars at:

IMG_0025.jpg

IMG_0021_1.jpg

Underground Car Park examples shot by me:

IMG_0565.jpg

IMG_0621.jpg

As you can see the cars match the location in a few ways ranging from colour, vehicle age and so on.

Factor this in on your next outting and you'll be onto a winner. :)

MSN me if you want to ask questions. :)

Edited by Xmetal

Hey Cara, you've got a nice car a few nice shot. The second set of shots are a bit too low in my opinion.

http://www.nissansilvia.com/forums/index.php?showtopic=9488

This thread has some pretty good information to improve your photographing skills. ;)

  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
×
×
  • Create New...