Jump to content
SAU Community

Recommended Posts

  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

  • 2 weeks later...

nope, just time consuming. take off the crossover pipe and associated pipes. take off coil cover. undo phillips head screws just under cam covers. then do the sam for the ones inside, just near the coils. then lift off, carefully not to ruin the rubber gasket.

now ur cams and stuff will be exposed, so close the engine bay ok. lol.

than sand and buff to your hearts content :(

probably takes 1hr for a newbie to do it.

nope, just time consuming. take off the crossover pipe and associated pipes. take off coil cover. undo phillips head screws just under cam covers. then do the sam for the ones inside, just near the coils. then lift off, carefully not to ruin the rubber gasket.

now ur cams and stuff will be exposed, so close the engine bay ok. lol.

than sand and buff to your hearts content ;)

probably takes 1hr for a newbie to do it.

ahh one hr would be no hassel, so is it worth replacing the gasket while the covers are off? How many screws in total (not including the coil covers ones obviously?) recommend putting a sheet or something over the engine??

Hame

yea mate, when u get off all the hoses, and the cam covers off yea, probably 1hr. from memory i think there is roughly 5-per side. and 4 sides, total probably 10-15+ screws. the gasket is rubber, and it is constantly lubricated with oil, so unless the engine is fkd, it should be in top condition, be careful, if it has never been replaced, it will most likely be stuck in the lid of the cam cover=dont lose it. just yer, make sure u close your bonnet, i had some hair getting in there from my dog. dont botha with a sheet, keep the bonnet closed. :P

I replaced the rocker cover seals in mine when i did the major service. Mine was leaking tho. When i pulled the old rubber seal out it did feel a bit hardened. But new seal kit was quite cheap so i just placed it. The kit i got came with rocker seals, moon seals, and all new rubber grommets for the screws that hold the cover on.

I would prob put a cover over the cams while you have the covers off. Also watch that those stupid gromments that go under the screws dont fall off the rocker cover and end up in the engine. I started getting worried when i counted the grommets and came up one short. Thought that it might have dropped into the engine or something. When i was cleaning up i found it under the car. Must have fell through the engine bay onto the ground. Lucky for me. I didn't really want to fish it out of the engine.

G luck

  • 2 weeks later...

well i going to give it a crack today!! so yeah i will watcgh out 4 that..interested in replacing the seals/gaskets, u get them from nissan?? how much?? n u have 2 use glue?

  • 3 weeks later...
  • 2 weeks later...

Hey Guys. Just started doing my cross over pipe today (using a sanding wheel on a dremmel). planning to get it all to a pre polish stage until i get a work vehicle next year. Then buff it all up at the same time. Plans are to polish cross over pipe, rocket covers, Plenum, Turbo heat shield, brackets in that area. All the rest of the bay planning to paint or put covers over.

Quick question. What is the easiest/quickest way of getting around the nipples / grooves / gaps in all the different bits?? Are people finding it easiest by hand on the tight bits? or would there be a tool/ dremmel attachment that would be quicker and more effective????

Luke...

  • 2 weeks later...
Hey Guys. Just started doing my cross over pipe today (using a sanding wheel on a dremmel). planning to get it all to a pre polish stage until i get a work vehicle next year. Then buff it all up at the same time. Plans are to polish cross over pipe, rocket covers, Plenum, Turbo heat shield, brackets in that area. All the rest of the bay planning to paint or put covers over.

Quick question. What is the easiest/quickest way of getting around the nipples / grooves / gaps in all the different bits?? Are people finding it easiest by hand on the tight bits? or would there be a tool/ dremmel attachment that would be quicker and more effective????

Luke...

I'm looking for the same answer as well. It is really really hard and sometimes impossible to hand sand the little grooves and indents and crevasses. The dremel tool attachments sometimes don't work that well either. Any input appreciated of course!

Great job. is it possible to polish the rocker covers if they are still on the engine

Ive done mine (well. got it all prepped for final polish) without taking the covers off apart. I just took taken off the coilpack cover, and all hoses/pipes etc that are in the road. then used wet sandpaper carefully to avoid any dust and stuff forming which could float off into unwanted places . After i had sanded back a section i wiped it clean. It came up pretty good. No photos just yet though won't have any till the local Australia day show and shine. But yeah. Doing it without pulling off is possible. Just be wary of rubbish that you polish off getting into nooks and crannys

Luke...

HmM i had alot of troubles when it came to sanding around groves etc. Just did it by hand btu took me ages. I guesss you could work on the covers while they are on the engine but it might be a bit harder on your back leaning over the car for hrs. A dremel or similar took might make the job alot faster tho.

  • 2 weeks later...
  • 1 month later...

u think maybe the rocker covers will eventually start to create surface rust from the scratched surface?

anyone found out first hand?

also are the moon gasket (rear camshaft gaskets a necessitity for when you also replace the rover cover gaskets?

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I know people cry at the price of the Getrag 12-14k for a conversion now, but it really is a nice mid point. Not going to get change from 10k on a gearset installed.  $30k++ for sequential.   I know you run the risk of a damaged used one and parts are hard to get but as a street car gearbox its really hard to beat. If you enjoy a more traditional manual, its the choice no question.     
    • Time to decide what’s more import, your power level or your budget because you’re going to struggle to keep both 
    • Our Southern Highlands Cruise is proudly registered with “R U OK?” Day.  Sometimes the best way to check in on your mates is by getting out for a drive together. Sharing a common passion like cars creates the perfect space to chat, connect, and support each other.  A simple “R U OK?” can make all the difference. Let's enjoy the drive, the company, and look out for one another. PLEASE WEAR YELLOW FOR “R U OK?” DAY Sunday 14th September 2025 9:30AM Meeting Crossroads Homemaker Centre 10:00AM Cruise Departure Via Old Hume Hwy 11:45AM Arrival at Mittagong RSL Club Meet Location: Crossroads Homemaker Centre Final Destination: Mittagong RSL Club *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yep, its been down for a while, as I understand it it will be back soon.
    • Yeah I also looked at Plazmaman, but, it ended up alot  cheaper getting black ones through EFI when you also added in the delivery cost
×
×
  • Create New...