Jump to content
SAU Community

1989 Manual R32 Gtst For Sale *sold*

AAR32

By AAR32,
in For Sale (Private Whole cars only)

 Share

Recommended Posts

AAR32 Rookie

AAR32

Posted
Posted (edited)

Hello,

My '89 R32 Gts-T is for sale due to a recent addition to the family :)

It is a 5 speed manual, has a genuine 122k kms (I bought it at 78k kms, 2005) and it's had the timing belt and water pump replaced at 95k kms. It has rarely been driven in the last 12 months as it has not been my daily driver, and there is no room for a baby seat! It has been serviced every 5000kms and during the most recent service I replaced the plugs (NGK Platinum) and brake pads (Bendix Ultimate).

The car is in great mechanical condition but has a few aesthetic flaws with damage to the front bar and a couple of pin dents, one on the bonnet and one just in front of the sun-roof. It goes really hard for a near-stock skyline and handles beautifully with the simple suspension mods! It won't take much to get it going quicker. I have been told it has a high flowed turbo but I can't confirm so I left it out of the mod-list.

It has been my pride and joy up until 5 months ago when we had our beautiful daughter and I have been putting off selling it but its time someone else got to enjoy it and I get used to driving a family car!

It is currently registered until the 14th of October 07 and I will sell with or without rego and with or without plates (AAR32) depending on price. RWC will be arranged upon sale.

Mods;

Engine:

* Unknown Pod filter (looks like Blitz but unsure :rant: )

* Turbosmart boost-tee

* 3' Mandrel Bent Exhaust with 3' Canon (from the cat back and turbo gaskets replaced January '07)

Wheels, Diff & Suspension:

* Genuine 17" Rays Engineering, Nismo Rims (Near new Sonar 215x45 tyres front and 235x45 rear)

* Tein Coilovers

* Front strut brace

* Unknown brand 1.5 way Mech Diff (fitted shortly after I puchased in '05)

Body:

* GTR Bodykit (Front bar damaged on lower front passaner side, and in the middle and mesh has been removed)

* GTR Grill

* Genuine aluminium GTR Bonnet (Small pin dent front middle)

* GTS-T wing has been removed so holes covered with red race-tape

Interior:

* R32 GTR Buckets (Drivers side wearing through around the bottom)

* MOMO Race wheel (Starting to wear)

* Carbon RAZO Gear Knob

* HKS Boost Guage

Price drop, $10,500

Please contact me (James) if you're interested on 0410 344 475 or e-mail [email protected]

Car is located in Maryborough, QLD

post-42599-1191738953_thumb.jpg

post-42599-1191739094_thumb.jpg

post-42599-1191739221_thumb.jpg

post-42599-1191739372_thumb.jpg

post-42599-1191739479_thumb.jpg

post-42599-1192955795_thumb.jpg

Edited by AAR32
Link to comment
Share on other sites
  • 2 weeks later...
  • 2 weeks later...
AAR32 Rookie

AAR32

Posted
  • Author
Posted (edited)

Hey guys, rego has now run out so i will sell cheaper as is for a quick sale, can also swap 17s for some stockish 15s (need new rubber though for rwc) for an even cheaper price!

Make some offers :ermm:

$10 500 price drop includes 17s, rwc and 6 months rego :)

Edited by AAR32
Link to comment
Share on other sites
  • 2 weeks later...
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • WMDC35
      Gran Turismo 7 Time trial

      By WMDC35 · Posted

      Blitz ER34 at some point hopefully, should be allowed in Gr3 if they do.
    • MBS206
      Blue Smoke from exhaust, RB25DE+T

      By MBS206 · Posted

      Stock R33 boost control, with the exhaust, and FMIC done, will boost creep. There is no tuning around it if it is the factory boost solenoid.   If it has an aftermarket electronic boost controller, the settings/mapping can be altered in it.   Oil could be anything as mentioned, however did it ever do it before you did the turbo swap? How much and how often did you drive the car before the swap?   I'm hinging on too much oil supply, or it's not draining properly.   To check, pull the air outlet off the turbo. Is it full of oil? Drop the exhaust at the turbo, does it appears to be oiled/coked? Now pull turbo and check the exhaust manifold, does it appears oiled and coked the same way?   Secondly, the PCV could even be stuffed / not functioning properly and will cause blowing of blue smoke.
    • hardsteppa
      Like loud exhausts? You could be a psychopath.

      By hardsteppa · Posted

      No "could" about it.
    • GTSBoy
      rb20de neo +t conversion - boost pressure sensor needed?

      By GTSBoy · Posted

      Almost any ECU would work, from a 30 yr old PowerFC to a new Motec/Autronic. But presumably you want new middle of the road ECU, meaning that you want a Haltech or a Link, most likely. As to which model though? I dunno. I don't keep track of what they have in their current ranges. You don't want a plug in though, because plug ins can start to cause you the same wiring issues that you have to chase up with your stock ECU/loom swaps when an engine transplant is involved. If you use a Haltech (and presumably a Link) you could put the base map for the engine in and drive it around and not even need to "tune" it. It will work just fine. I can't recommend a tuner without a location (and even then I can't recommend many, being as I never use any tuners except myself and my brother-in-law). And not many tuners are happy to remote tune. Maybe they'd be happier doing it for a basically stock setup that just needs to be demonstrated to be working properly. But even then, not being able to be with the car to see what the hell is going on and sort out the inevitable problems that will result from an engine conversion done by an amateur..... unlikely to be enthusiastic about the job. And if you think that just adding 2 wires for the boost sensor is difficult - you don't want to be trying to install and set up an aftermarket ECU. You're going to have to bite down hard on something with either approach.
    • deuceforty2
      Wiring loom difference between A31 A/T RB20DET and R32 M/T RB20DET?

      By deuceforty2 · Posted

      wired everything up and confirmed that the red with white stripe is indeed the fuel pump pin on this harness. 
×
×
  • Create New...