Jump to content
SAU Community

Recommended Posts

if tangles happens to wander through here,

been reading through the 'rise and rise of kevin rudd' thread in the wasteland to kill time, and i like the way you think mate. :)

Bosch 023 is the next step up from 040 and can handle roughly 200hp more (~800hp) , and it still fits in-tank ?

That true ?

Is it worth getting this just to be safe (unsure how hard to push the engine at this stage...) ? I saw 1 on ebay for ~$195 delivered. (Says its genuine Bosch). Steer clear of ebay 1s and go get it from a shop ? Anyone using this pump ?

Thanks

Edited by KISIN

Does anyone know who would be best to fix up the trim on my Momo Wheel? it is splitting at the seam, but the condition of the leather is still good, so looking for someone (motor trimmer perhaps?) to essentially glue it back together with the correct adhesives.

Cheers

i have what i thought was a 32 gtr wheel, but appears to be a 33 s1 wheel

had it since january....horn didnt work cos of a different setup to the 31

has a slight worn patch at about the 7 o clock position

if it works for ya steve ya can have it

http://www.drambuieresearch.com/

Hmm bogans and drambuie do they mix lol :cheers:

ROFL i heard you like it but...

can anyone answer this

ORC TSUINPURETOKURATCHISETTO RB26RB20BNR32BCNR33

will that clutch suit a GTS4 push type ??? :w00t:

this is what i want to get

also does anyone know how much meat is " Disk remaining two are 4.07 mm so still usable. "

chibaken_chibasi-img600x450-1196684723p1000889.jpg

chibaken_chibasi-img600x450-1196684735p1000890.jpg

i had 3hrs sleep today and had to go to observation day thingo with

this place i had an interview with on Monday.

it went quick so it was good ;)

oh my brother bought another Celica :rofl: , it's manual so

i'll be learning manual in that when they get it registered

(hopefully next week)

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
    • Hi.. Just another problem. So maybe you can help. I(my mechanic) done swap from my RB20DE NEO to RB25DET NEO. Everything is OK but we have a boost cut. Coils/Plugs are ok...AFM is ok. ECU is ok. I have Walbro 255 but it "changed" sound few months ago(you can hear it ouside) you did not hear that when it was new(maybe faulty?) Sooo...what now? What can cause this boost cut? It is even when you standing still...
×
×
  • Create New...