Jump to content
SAU Community

Recommended Posts

tangles, dont tell me we cant sink a few while doin the actuator!!?!!!!??!???

hehee jks

lol I pm'd you last night with that info, 'cause I was embarressed that I dont have any even after offering it in the actuator thread; was playing on my mind (Im a man of my word)

:D

Im a bad panda, sorry ;)

(unless some1 reads this and pms me, lmao)

I'm bored.

I was looking on that Kansai motorsports website and saw R32 GT-R coilovers.. (2nd hand)

Nissan R32 Gtr coilover kits aftermarket shocks and springs

$550

Nissan R32 GTR KTS coilovers

low kms damper adjustable and base height adjustable

$1,250

Would that stuff fit my GTS-t?

Edited by muirsky

Had a mate come over last night. We stayed up drinking until like 1.00 in the morning!

He's real keen to buy my Stagea. Once he sells his VX ute he'll be throwing some cash my way for a deposit.

:D

Nah, he came over to talk about buying my silver Stagea (not the black one sorry if I fooled yas) and we got into talking about some of the guys we ride with, and then drinking a bit.

But he loooooves the Stag.

:D

Nah, he came over to talk about buying my silver Stagea (not the black one sorry if I fooled yas) and we got into talking about some of the guys we ride with, and then drinking a bit.

But he loooooves the Stag.

:D

do you drive the silver one much ruby?

Gee id love to be you in the morning. "hmm what should i drive today, the black or silver stag? or maybe ill ride one of my bikes.."

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...