Jump to content
SAU Community

Recommended Posts

Lowered springs or Coil Over???

i have tein hr's and i love them.... stiff as all hell, and up untill recently was my daily.

if u have a GF that loves to complain, get the lowered springs, they will make her boobs bounce less (can be very distracting out of the corner of ur eye :thumbsup:)

much like the boobs down here

Nah daily driver but want the beter drive, thats why i come to the master's for there personal opinion?

id say good shock and custom spring combo.

but, if you go after coilovers, jump onto import monster, have a browse and see what you can find, theres some damn good gear for sale on there.

i have tein hr's and i love them.... stiff as all hell, and up untill recently was my daily.

Im exactly the same, have HR tiens in the 33...stiff as all f**k, i carry a kidney on ice in the boot. Was my daily for a year or so, but still drive it occasionally. On a normal route you tend to remember where all the bumps are. hehe.

yeah currently 4000kms into the current Motul turbolite 8100 10/40w

got 2 for one a year ago.

hhhhhm not sure, might just let the tuner take his pick :thumbsup:

Are u sure its turbo light 8100?

The turbolight is a semi-synth grp III oil where as the 8100 is a full synth grp iv oil.

The so called 'synthetic' castrol is only a grp III based oil. So not really a full synthetic in a pure sense. There was a court case years ago; they won on technicalities and were allowed to sell a group III oil as a true synthetic. Many then followed (valvoline, shell amongst a few others).

Motul, Royal Purple, Mobile have all stuck to the synth is synth and not ripped off the cust in that respect.

But either one.. the Motul is better value for money; the castrol your paying for crap but it still works fine.

I've ran Motul 8100 5w40 since day dot in the rb30det (~80,000km's) bores looked brannew and the head was super clean when it was pulled off not so long ago for valve springs.

For what you get it is the best value/performance oil u can get at the $60-$75 price point.

pancakes were junk :D

people who came :P

they werent that bad but not as majical as i expected tho! banana milkshake was teh suck and survice...... hmmmmmm i bit left to be desired.

next time we go MEXICAN!!

highlight of the pancake kitchen. good company.

they werent that bad but not as majical as i expected tho! banana milkshake was teh suck and survice...... hmmmmmm i bit left to be desired.

next time we go MEXICAN!!

highlight of the pancake kitchen. good company.

heh mexican. Zapatas on Melb st is good. Nothing like having a small mountain of nachos taking over yr entire table...

-D

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • UPDATE: Yes the GSP Axles are compatible. I installed it on my R34 today and they are working a treat! Turns out that the S13, S14, S15, and 200 SX all used the same axles as the HR34, and ER34 NA models. Which is 2 bolt x 3 pairs.  
    • Also build this EH ute with 370z motor and gearbox with a couple of turbos just for fun.  
    • Got the passenger door on plus the master cylinder and booster. Loaded up to take it home. At home, the colour changes a lot in the light.
    • Nothing cheap, but I have seen the AC Hydraulic DK13HLQ which is pretty close to what you're asking for. The problem is the hydraulic cylinder mandates that the back of the jack be a certain height and Skylines have fairly deep inset floor jack points. A more certain and cheap option is to get some nominal 2x10 inch lumber boards and have one board be 1.5 feet, the other board 3 feet. Glue it all together with lots of clamps to maintain pressure. Make two of these. The ramp suggested above is a good idea, it takes quite a bit of clutch slip to get over each of the boards. I only need the first ~1.5 inches for my low profile jack on a standard ride height car but a lowered car you want to go up to the full ~3-3.5 inches. Paint it or store indoors if you want it to last.
    • Ok. And Nistune? I read (here too) mainly on Stagea threads that it can by "turn off" with Nistune. But they say they still had the sensor plug in. Next week iam going to the Nistune(and other ECUs) tuner so i can finally make it work. I drove the car home and apart from the cut it drove great. No misfire no smoke no hesitation or rough start...so hoping it is this sensor that is missing  
×
×
  • Create New...