Jump to content
SAU Community

Recommended Posts

Very productive day again today! Water pump, belts, coilovers, coilpacks, and more importantly, MY COOLER! The fan hits the crossover pipe and ticks like a clock on speed, we didnt have enough time or tools to properly cut all the shit out of the front bar, so it sits 2cm forward and relies on 5 cable ties for support, but i love it.

Yeah we are going to finish it all off next weekend, i dont drive it during the week anyway so it will be fine until then. Kellie earthed my boost solenoid too, couple more pounds, pulls so much harder through 2nd and 3rd now!

Yeah we are going to finish it all off next weekend, i dont drive it during the week anyway so it will be fine until then. Kellie earthed my boost solenoid too, couple more pounds, pulls so much harder through 2nd and 3rd now!

hey damien, did you earth it via a switch or did you just earth it so its constant?

interested in doing this boost solenoid trick

was the difference noticeable?

Hey Pete,

My mate had one in his s15. Setting them up takes awhile but once all set they work like a dream.

Other option i would be looking at would be a profec B.

Thanks for the reply Luke.....I already bought it cause I was told it was the best on the market (definitely the dearest).

I didn't realize there were so many features to setup......I suppose your mate set it up himself so at some stage I'll sit down with the instructions & have a go.

On the matter of belts, waterpump & gears, we may have to have a chat about your rates sometime Ryan.......I've got a workshop full of gear but no time to scratch myself lately.

someone sell me there rb25det series 2 engine pack for like real cheap :)

Ha. I could sell you one, but it comes with a Stagea. Not cheap ;)

I WANT RB25!! had my first drive in one today! so jelous!

Hmm, I recall you and Min came for a spin in the Stagea not long ago! :D

:D

Anyone know the name and number of the shop on henley beach road that sells work safty gear? Iv been searching for it but i cant remeber he name of the place, i need new work clothes and boots

I reckon you're talking about 'Yakka Aust Menswear' corner of Henley Beach Rd & Clifford St, Torrensville.

Also try 'Aust Safety Specialists' 16a Ashwin Pde, Torrensvile (just up the end of Clifford Street)

Thanks for the reply Luke.....I already bought it cause I was told it was the best on the market (definitely the dearest).

I didn't realize there were so many features to setup......I suppose your mate set it up himself so at some stage I'll sit down with the instructions & have a go.

On the matter of belts, waterpump & gears, we may have to have a chat about your rates sometime Ryan.......I've got a workshop full of gear but no time to scratch myself lately.

I'll ask my brother about it, cause im sure he wired it all up. he might be willing to help wire yours up or give you some info. I'll ask him and let you know.

edit: spoke to my brother about it. Wiring it up isnt that hard its just setting it up. You basically have to do street driving to get it set up correctly. Its awesome for holding boost, whatever level you set it at it will hold it, but when it comes time to up it more it can be a pain. If you want it at one level i would suggest leaving it at that.

Edited by Luke_ENR34
I'll ask my brother about it, cause im sure he wired it all up. he might be willing to help wire yours up or give you some info. I'll ask him and let you know.

I've got it all wired up Luke but it just needs all the parameters set up properly otherwise a setting for 10psi can boost as high as 18psi if not configured correctly

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
×
×
  • Create New...