Jump to content
SAU Community

Recommended Posts

hey Joel.....did you have to retard the exh gear to compensate and bring the power curve back to the left?

I'm abit confused, cause even though 9mm is not huge lift, when I went to school, bigger overlaps always caused a shift in rpm in a northerly direction.......maybe it's more to do with your tune than the cams cause I always thought that better response is not generally a side effect of bigger overlaps :blink:

:laughing-smiley-014: Back and to the left........

ahh ok.......sounds like an Ivan Tighe grind.

I though you may have been running a Poncam, HKS or similar cause they all run bigger overlaps than stockies

Tighe regrind it was.

I stumbled upon a list of HKS, Jun and LCA's but be buggered if I can find it.

I do remember the Rb20det's definitely had the same 110 and 115 LCA's when running in the 264 duration range.

Rb25's.. 115/115.

Tighe regrind it was.

I stumbled upon a list of HKS, Jun and LCA's but be buggered if I can find it.

I do remember the Rb20det's definitely had the same 110 and 115 LCA's when running in the 264 duration range.

Rb25's.. 115/115.

So would u recommend me get cams if I'm getting camgears, turbos, and injectors (and their support mods, fuel pump, water pump, afm, gaskets)... and if so, what type? I know nada about engine physics

-D

Cams always help make the power easier..

Don't overcam it. I was a little nervous 265's were a little too big but Shaun has had good results with that type of duration on fairly stock rb30det's previously so I went with his advice.

yeah we used to deal with Tighe Eng many years ago when I was still at Adelaide Eng, so I've considered going with one of his grinds as opposed to alot of the Jap stuff out there.

Good thing about them is that they don't just grind a second hand cam then end up with undersize lobes that have gone through the hardening process but instead they either start with a new billett or build up the lobes first. I find that alot of the jap grinds aren't really considering the average Joe that needs to drive to work through peak hour.

Sometimes I wish I still had access to our cam grinder and all the various masters that we had cupboards full of.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...