Jump to content
SAU Community

Recommended Posts

Grab some carby clean. They almost always gum up and cause idling issues.

Does the valve AAC valve need removal for cleaning?

If its idling too high there's another valve that may be the cause. IAC valve. The spring can dislodge and cause a constant 1000-1500rpm high idle.

Can the spring be relocated or would I need a newbie......also can a good hammering up the hills cause a dislodgement because its been like that ever since I went for a run with my mates Porsche & Maserati (gave it a bit of a hammering that day :blink: )

Yeah mine idles way too high. I'm guessing the AAC valve is the accessible the one near the fuel filter which can be cleaned whereas the IAC is probably the "cold air by-pass solenoid" which is against the sandwich plate under the centre throttle body which requires a plenum removal and which can't be cleaned (approx $220 new).

Also Cubes, have you got the full specs on your Tighe cams ie. IN & EX opening & closing times etc......I might look into them myself.

Can the spring be relocated or would I need a newbie......also can a good hammering up the hills cause a dislodgement because its been like that ever since I went for a run with my mates Porsche & Maserati (gave it a bit of a hammering that day tongue.gif )

I do have the cam sheet. All though your requirements will differ as you are blessed with solid followers.

Tighe did reduce the base circle some what however it doesn't appear to have created any problems.

http://www.skylinesaustralia.com/forums/in...t&id=173055

Unsure if a hammering can cause it to dislodge.. Possibly.

Grab a can of start ya bastard and check for vac leaks bfore you go to the trouble of pulling everything off.

If the spring flicks off you can hook it back on and secure it a little better.

The std gasket will most likely break so grab some ACL gasket paper (the hard yellow paper) as its the correct thickness.

how hard is it to un wire gtr injectors with resistor pack??

If you have used a 280zx/R30 style resistor pack its as simple as heading down to the local auto store picking up a Navara 8pin? from memory plug and connecting each pin to each other (bridge) via wires. Then remove the resistor pack and plug in the bridged plug.

Hey guys just a quick question, i have a massive coolant leak at the back of my engine im pretty sure its just the heater hose leaking, any ideas how hard this is to replace??? or any idea's what the leak could be from its right at the back of the enging just infront of the fire wall.

hmmm I seem to be having absolute shit luck this year. Swapped the Chaser for a stupidly worked JZX81 track car and a Cressida Grande. Over valued the cressy to the tune of like 3k, turns out the thing is fair f**ked. Lost my job so had to swap the 81 for the 32 I'm in now, didn't get anywhere near enough coin on top. Lost about 6 grand or so in those 2 transactions. Now the Cressy has blown a head gasket (even after being torqued to the proper specs - good old 7M :() and the 32 is missing 1x rear quarter.

Roll on 2009 :)

Anyone know how to untighten the screws on the front of the fuel rail? Or what i can put on there so its easier to get them out? In heaps tight and i need them out to replace the o rings. Start fixing some small problems before i start driving it again in 2 months.

hmmm I seem to be having absolute shit luck this year. Swapped the Chaser for a stupidly worked JZX81 track car and a Cressida Grande. Over valued the cressy to the tune of like 3k, turns out the thing is fair f**ked. Lost my job so had to swap the 81 for the 32 I'm in now, didn't get anywhere near enough coin on top. Lost about 6 grand or so in those 2 transactions. Now the Cressy has blown a head gasket (even after being torqued to the proper specs - good old 7M :( ) and the 32 is missing 1x rear quarter.

Roll on 2009 :)

Aren't Cressy's prone to warping head gaskets? My mates Cressy which had a 5M in it blew 2 head gaskets within 6 months :D

Yeah man cressys eat gaskets like they're goin out of fashion :) Its the head torque that is the problem. Mine has been re-torqued and still fked the gasket out (to it's credit, it did complete about 10kays worth of driving on the H with the bottom end rattling away before the head gasket went :))

I reckon I'm just gonna get a Falcon and stop spendin money modding cars for a while. The Falcon seems to be best suited to daily with occaisional towing duties, so I can still get the busted arse 32 out to the track to thrash, Crazy Max styles with munted rear quarter. At least if I hit the tyres on the entry to 1 it doesn't matter because that quarter is already f**ked :laughing-smiley-014:

what suspension matty?

kyb shocks, aurora springs.....7kg front, 5kg rear, standard size (but slotted) aus del front and rear brakes too................nothing special in pads, and they didnt fade or cook

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...